axial wraith lift kit 3d models
74271 3d models found related to axial wraith lift kit.cults3d
hood, fenders, doors and roof for axial wraith the exhausts will be coming soon for the hood turbocharger https://www.thingiverse.com/thing:2808785 thanks to Hauflo for his beautiful realization ps: to facilitate printing, the roof is printed flat,...
thingiverse
Lift kit for all Axial SCX10 based RC trucks. Adds lift of 14, 20, and 26mm if the lower of the two upper mounts is used, the very top mount adds another 5mm. Pictures show mounting using 3mm hardware into the plastic (could use longer bolts + nut if...
myminifactory
A replacement wishbone for an Axial SCX10 RC Crawler with lift kit. The lift meant the drivershafts were fouling the wishbone so I made new ones. ...They are slightly longer to adjust the axle for the lift also.
cults3d
RC GANG 93 Shielding kit type MAD MAX adaptable to AXIAL WRAITH https://www.youtube.com/watch?v=fNWg0yyTxMhY https://www.youtube.com/watch?v=fNWg0yyTxMhY
thingiverse
Simple 10mm Lift Kit for the SCX10 to retain stock suspension geometry. This is non adjustable and designed specifically for the Deadbolts 12" (305mm) wheelbase which uses the outer holes on the stock shock hoops. May fit other SCX10 depending on...
thingiverse
I printed some parts to lift the suspension of my crawler. Unfortunately the driveshaft was fouling the upper wishbone. I have designed these to avoid the fouling and they are slightly longer to adjust the angle of the axle too. ...Print Settings...
thingiverse
Axial Wraith Mirror I used cura to slice,so i just mirrored the other side to print both.
thingiverse
hinge for rc car axial wraith use for hood plate for magnetic hood: https://www.thingiverse.com/thing:3157126
cults3d
Axial Wraith Mirror I used cura to slice,so i just mirrored the other side to print both.
thingiverse
Trunk for axial wraith. 2mm thickness no holes for screws holds without them. ... Rear inner fender by jruutiai https://www.thingiverse.com/thing:2804455
myminifactory
Fully adjustable trailer hitch for the Axial Wraith. No support needed. I used 0.25 triangle fill. Printed in PLA and ABS. ...Bolts directly to the original bolt locations.
cults3d
this is a conversion to fit a element ifs to a axial 1.9 wraith modification required on intermediate skid to fit included reciver box my pics include a high clearance set up (not required) from thingiverse at this link...
thingiverse
bolts directly to the roof of a axial wraith but will fit many different scale trucks. I printed the bar in PLA and the mounts in TPU. both in TPU would probably be better. I used a standard led strip. you have to get creative with the soldering...
thingiverse
I designed this piece for those modifying and Axial Wraith / Spawn to classic panel body type crawler. This serves to close up the lower rear section of the tube chassis. Can be installed ass is looking like a tail gate or as a base for radiator...
thingiverse
This is a simple fairlead for the Axial Wraith. Mainly applicable if using a servo winch setup. Designed around the stock servo on axle setup, I have not tested with a CMS setup, and I don't have any interest in putting CMS on my Wraith at this time....
cults3d
This is a simple fairlead for the Axial Wraith. Mainly applicable if using a servo winch setup. Designed around the stock servo on axle setup, I have not tested with a CMS setup, and I don't have any interest in putting CMS on my Wraith at this time....
thingiverse
A bumper I have been wanting to make for my wraith I didn't like the options the aftermarket had available my wraith suspension is set low so there is clearance for the servo modeled in
thingiverse
This is a shorter RollCage for Axial 90056,let you Axial car look nice and can carry a spare wheel,have fun!
thingiverse
good news i was board and updated my wraith/clod project to lessen some steering problems and suspension geometry theres two new side plates and 5 supports, all links same just relocated moved lower link on axle. had the idea to mod my wraith with...
thingiverse
Why i created this I bought the 4 wheel stear kit, and i needed an mount of the servo which was hard to get an original one. I ordered an unoriginal but while i was waiting i used this one. Worked perfectly a whole day on the front wheels. Fell off...
thingiverse
This kit is for mounting servo on the Axial Wraith cage. ... 4 holes to adjust panhard bar.
grabcad
Axial Wraith Front Bumper Bracket, secures front bumper to cage
thingiverse
Box front axial wraith recever and led Print with https://www.thingiverse.com/thing:3914534
thingiverse
light-bar for Axial's Wraith 1/10 rock racer which replaces the stock front bumper.