axio scope a1 3d models

A GoPro 2 mount is available that attaches to a gun scope measuring 41.5mm in diameter (like my Gamo scope). You can purchase a #6-32 x 1.25" to 1.5" tightening bolt from Home Depot. Installing the camera is simple, requiring only one hand, but...

Simply enter your scope's diameter and bell housing length, and you'll get a custom-made scope cap. Print Settings: * Printer Brand: LulzBot * Printer: Mini * Rafts: No * Supports: No * Infill: 100% Important Notes: If using flexible filament,...

The side Scope mount on an Airsoft SVD offers versatility, allowing for easy attachment of various scopes without altering the original gun's layout. ...By following this straightforward assembly procedure, you can achieve a solid and level platform for...

A Picatinny rail and NATO-standard scope mount are compatible with the CZ452 rifle, providing enhanced versatility and customization options for shooters.

Just my design of a raspi camera v2 mount for the SV28 Porro Prism Spotting Scope. ...Super Simple it just works.

The optical scope is magnified at 8x, featuring a texture size of 4096x4096 pixels. ...The rendering style used is default scanline for a high-quality visual representation.

THIS WAS JUST A WAY TO PASS A RAINEY DAY LOOSELY BASED ON A UNERTAL TYPE MOUNT COULD BE 3D PRINTED BUT WHO NEEDS A PLASTIC SCOPE MOUNT

Bubble level for scopes with 1" tubing. Needs three M3 bolts, nuts and the level (9.5 mm diameter, approx. ...25 mm length)

This is the foundation base for Yngel's M38 scope adapted specifically for the E11 Stormtrooper Blaster, enlarged slightly to accommodate a 40mm pipe structure.

The adapter fits on a TS Optics 8x50 mm finder scope with 180 mm focal length (https://www.astroshop.eu/optical-finders/ts-optics-finder-8x50) but can probably be modded for other finder scopes as well. You can determine the focal length of your...

A simple adaptor that allows you to take the Svbony (non-name brand) Guide scope and attach it onto a Skywatcher tube ring using the screws that comes with both scopes. Here I've used 2 1/4 inch camera screws to clamp down, I recommend 20% infill...

... for a way to mount a Scope on my old 30.06 without damaging it. ...So I made my own mount the shop is building it for me know I hope it works. As a bonus I put hole into the mounting block so the peep site can still be used looking under the scope.

Created this to quickly adjust magnification on the Vortex Strike Eagle 1-6x scope. The inner diameter is 44mm so I'm assuming any scope that has the same adjustment should be able to use this. ... I used a 2.5mm bolt and nut to tighten this onto the...

Remix for a Larger Scope Tube Bubble.\r\n\r\n\r\nFor 30mm Scope Tubes.\r\n\r\nRequired Hardware:\r\n1 M3x16mm Screw\r\n1 M3x25mm Screw\r\n2 M3 Nuts\r\n\r\n1 35mm x 8mm Bubble Level.

I needed a straightforward phone adapter for my Hawke spotting scope. Instead of an intricate fastening system, it relies on a simple rubber band to secure the phone in position. A future iteration might incorporate a dedicated fastening device for...

Engineered to seamlessly integrate with standard 25mm scope mounts, this rail provides a sturdy foundation for optics systems. Strategically positioned holes accommodate one M4 bolt on either side, ensuring a rock-solid attachment. ...Measuring 6cm in...

I kept looking for full scopes for Airsoft scope since i didn't want to buy a real one so I just made one. All the assembly is fit together with M4 screws and bolts. Not sure on the length yet but there is a possibility of gluing it. ...Please leave a...

This is an air scope model design intended for old Yamaha Jupiter MX vehicles, with a disk brake diameter of 220 mm. ...This air scope helps to clean dirt on the brake pad and removes braking heat so the brakes don't fail

This is an air scope model design intended for old Yamaha NMax vehicles, with a disk brake diameter of 220 mm. ...This air scope helps to clean dirt on the brake pad and removes braking heat so the brakes don't fail

night vision scope bolt on 44mm max scope 1 x100 mm screen 1 x CMOS cam board 4 x m4 hex scocket cap bolts 4 x m4 rivnuts 3mm perspex mirror 45mm x 54mm 45mm x 60mm 1 x USB flex cable 1 x MT3608 DC-DC 3v-5v to 12v or just 12v

These are shims used to elevate the rear of the Celestron Red Dot finder scope so it can align with the target point of a Celestron telescope. ...I utilize these on my Celestron 130EQ because I discovered that the finder scope ran out of adjustment...

I wanted a larger throw lever than what was available on my CVLIFE Scopes(https://a.co/d/29N7bz1). Let's the gun go into my cases. Uses M3 x 12mm Screw and nut. ... Added V2 which is thinner and more rounded for lower profile scopes.

... Calculate: (Outer Diameter of your Scope End) / 41 = Scale Factor Example: You need a 47mm ID, calculate: 47/41=1.1463 Scale by 1.1463 (or multiply by 100 for percentage) = 114.63% If you scale significantly, you may need larger screws and nuts.

Quick zoom adjustment aid lever for shooting scopes. Lever made of PET, a more resistant printing material than usual. Files available from 38mm to 48mm. ... Accessories: 1 Allen screw M3x20, 1 Nut M3 If you want a diameter in articular let me...

Someone asked for the Picatinny mount version of a Nerf Vortex Nitron scope that someone originally designed for Nerf rails. I remixed the original part to fit a Picatinny rail. Secures with a 10-32 x 1" screw and a 10-32 x 5/16 nut (McMaster in...

After printing the tool the ring needs inside a 1mm layer of foam rubber like this: https://www.amazon.de/gp/product/B0792K5PQS/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&th=1 I used this tool to remove the polar scope in a Skywatcher EQ6R-PRO. It...

The scope features 50mm front optics, encased within a 60mm outer diameter casing, so the protector will fit perfectly on a tube with the same diameter. Recoil is not a concern here since I am using the scope in a PCP air rifle. I will post images...

I was able to mount a crosman 4x targetfinder scope with this scope mount. ...I then added the extended version to be able to also mount a magazine that was posted by: k19k19-https://www.thingiverse.com/thing:2274721 You will only need the following:...

The finder scope is positioned further away from the telescope than the original since I thought the original was too close. I used 6 M3 x 0.5 screws to secure the scope. I drilled and tapped the holes in the model after printing. ... Picture also...

... the position of the holes onto your Open Sight Carry Handle and drill them out. Glue the bolts into the rail mount and THEN glue the rail to the scope. After that, simply attach the scope with rail to your carry handle and tighten the wingnuts on.