azdelivery esp32 devkit v4 3d models
12775 3d models found related to azdelivery esp32 devkit v4.thingiverse
This is a Snap-Fit Case for the latest ESP32 Devkit v4, which has (compared to the Devkit v1) a smaller PCB without screwholes and where the antenna is sticking out. As far as i can tell, there are no other cases for the the Devkit v4, which i why i...
thingiverse
A small outdoor housing for thermometers or other stuff using a 16x2 LCD an a ESP32 For a sleak design with a separate break out cable box, conencted to the ESP-housing with only one cable. ... Have fun with it
thingiverse
1 modèle : - Aerator Wifi Style --------------------------------------------------------------------------------------------------------------- I wanted a little ventilation for my ESP32, and as I really liked the wifi design for other ESP models, I...
thingiverse
Box für einen ESP32 und eine 2 Relaykarte. ... Code für Loxone <--> Hörmann UAP1 https://github.com/Ulmer-spatz/Loxone/blob/main/Garage.ino Remix von https://www.thingiverse.com/thing:4730585
thingiverse
I needed a housing that is very thin and gives the antenna free space. Here it is. ... A piece of white paper folded in three is sufficient for to hide the red LED.
thingiverse
ESP32 DevKit C Board Case Fits For AZ-Delivery CP2102 development Kit Buttons built into the top allowing user to press on-board buttons without removing the cover
thingiverse
This is a remix of ESP32 DevKit V1 Case (Thick). ...The only difference is that both parts now lay flat on the bed rather than 1cm in the air for the top.
thingiverse
This is ESP32 devkit v1 case. Please leave comments if you want me to improve. If you found this useful, please donate what you think it is worth to my paypal.me. Help cover the time of design. ... Thanks, Enjoy!
prusaprinters
Case has cutouts for USB, LEDs and pins will stick out of back of case. If you want a version of this case where the pins are fully shelled/enclosed - see: https://www.prusaprinters.org/prints/50035-esp32-devkit-v1-chunky-case Print instructionsFront...
thingiverse
Remix of BKGoodman's ESP32 DevKit Case with the following modifications: 1. Extended case bottom to cover and protect ESP32 pins (female Arduino jumper wires fit perfectly in the slot) 1. Slightly taller base to allow top to close properly 2. More...
cults3d
This is a small enclosure for a ESP32 DevKit board (available at aliexpress). It has openings for USB and a few small cables. I created this for my CNC mill as a websocket controlled illumination (from within bCNC) (WS2812 LED ring) for my router.
thingiverse
Attention!! ...This case for a narrow board with a non-standard width of 25.5mm I strongly advise you not to buy such a fee. But if you have already purchased it, here is the case for you. ESP32 DevKit case
thingiverse
This is a small enclosure for a ESP32 DevKit board (available at [aliexpress](https://www.aliexpress.com/item/MH-ET-LIVE-ESP32-Development-Board-WiFi-Bluetooth-Ultra-Low-Power-Consumption-Dual-Core-ESP-32/32820820998.html)). It has openings for USB...
thingiverse
Has 2 holes on top for LED visibility, and buttons built into the top of the lid which allows user to press on-board buttons without removing lid.Note that I had previously said this works for a "NodeMCU" board - but it's actually for a "DevKit"...
thingiverse
A simple case to house the ESP32s I got from amazon **BOM** *None of these links are affiliate* - ESP32 - https://www.amazon.ca/dp/B0B3MY3P9T - Antenna - https://www.amazon.ca/dp/B07X5XD4NR **Features** - USB slot for programming after installed -...
thingiverse
... box without having any shorting/breaking issues. I made this ESP32 box to house the clone development board. While at it, I also make the marking to easily identify the pinout of the ESP32 pins. ... Hope it is off use to someone else too...
thingiverse
I looked for a case for my ESP32 project but none of the ones on Thingiverse really appealed to me. So I took bits and pieces that I liked from them and made my own. I included the openSCAD files in case you want to modify it to suit yourself. Note...
thingiverse
Case for the ESP32 devkit module (38 pin). I have the one from AzDelivery which fits perfectly. Not 100% sure if all the boards fit. You can click the board in place on the 4 small standoffs. This case provides access to all the pin headers and an...
thingiverse
Attention!! ...This case for a narrow board with a non-standard width of 25.5mm I strongly advise you not to buy such a fee. But if you have already purchased it, here is the case for you. ESP32 DevKit case v2
thingiverse
This is newer version of my ESP32 DevKit V1 case, suitable for 3D printing. It has an exposed USB port and a snap-on lid with ventilation, LED cutout for viewing onboard LEDs, and two buttons built-in which less you depress the on-board ESP32 buttons...
thingiverse
Completely customizable, even the devboard measures, so it can be used with any board (not only devkit v1)
prusaprinters
This is case is used to take an ESP32 DevKit-V1 which can run off battery power - i.e. no wires. So - I wanted a cheap and easy way to battery power my ESP32. But - A normal AA battery is rated to about 50mA, and only runs maximally at 1.5v. So even...
thingiverse
Simple case for my ESPresence system - needed a proper case for the Adafruit ESP32 Kit... ... https://www.adafruit.com/product/3269 Print at .03 layer height No need for supports - laying the flat tops on the bed....
thingiverse
I remixed it to be able to remove pin holes (really hard to match with the board). ... Probably in the future i will add some stand-offs for ESP32 mounting holes and enlarge alla round to make it fit better... ...now the size is soooo perfect
thingiverse
A case for the ESP32 devkit with the possibility to install an antenna. ...Both buttons of the devkit are accessible.