azteeg x5 3d models

Azteeg X5 V2 Mount. Mounts on 20mm V-slot Tap holes or enlarge for 3m screws. ...Print Settings Printer Brand: LulzBot Printer: ...

A tray to hold the Azteeg X5 Mini, allows cooling to run under board, and leaves sides and top clear for wiring. Board should just snap on. ... Added tabs to allow attaching to extrusion.

This is a case that the Azteeg X5 Mini will fit into, making it easy to not accidentally have a short circuit, and of course to organise all the wires.

This is designed to place the Azteeg X5 Mini with the usb connector close to the outside of a kossel vslot 2020 based printer. I've added a central bar to make it less flexable, and also added m5 mounting holes. ...I put the standoffs on the outside,...

SummaryThis is designed to place the Azteeg X5 Mini with the usb connector close to the outside of a kossel vslot 2020 based printer. I've added a central bar to make it less flexable, and also added m5 mounting holes. ...I put the standoffs on the...

mount for the azteeg x5 mini v3 optimized for the kossel pro (15mm extrusions using m3 hardware)

Really basic Azteeg X5 GT mount designed for the corner of the Voron printer(2020 Extrusion). ...Plastic standoffs were used to connect the controller to the mount.

I wanted to keep this Rumba case so I modified it win Fusion360 to fit the Azteeg X5 mini V2. Also added a slot below board to allow my wires to enter from between my horizontal extrusions. ...Update 5/19/16 Removed a few old standoffs and tidy up...

Box that I re-lofted to accommodate the Azteeg mini X5 V2. I like the design of the source box but just didn't fit the V2. R01 changes the size of the card slot and usb. (was a bit too small when I printed mine. Print Settings Printer Brand: ...

This is an Azteeg X5 mini v1.0 mount that I designed for my kossel mini.

May work for other versions of the Azteeg X5 Mini but I only have version 3 so I can't confirm. ...Print Settings Rafts: Doesn't Matter ...

Remix of cas000176's Azteeg x5 mini V2 box: http://www.thingiverse.com/thing:1613637 Added two holes centered along the bottom to allow mounting vertically on t-slot extrusion. ...Holes are sized for M3 hardware.

This is a simple mounting plate for an Azteeg Mini X5 V2 to be used on my mini-Kossel (with 2020 rails). ... Print Settings Printer: Mini-Kossel ...

Faceplate and mount for azteeg x5 mini v3. I don't have wifi version but just slight modifications to faceplate may make it work. Faceplate mounted with 4 M4x8 button head screws and mount with 2 M5x8 socket head screws. Azteeg is held by faceplate...

Faceplate and mount for azteeg x5 mini v3. I don't have wifi version but just slight modifications to faceplate may make it work. Faceplate mounted with 4 M4x8 button head screws and mount with 2 M5x8 socket head screws. Azteeg is held by faceplate...

This is a fan duct to cool the stepper drivers on the azteeg x5 mini v3. It holds two 30x30x10mm fans. The fans are offset and positioned evenly above the stepper drivers. Use #4 screws to mount it to the board. Use another #4 screw to clamp the two...

Azteeg X5 Mini:http://www.panucatt.com/azteeg_X5_mini_reprap_3d_printer_controller_p/ax5mini.htm . Smoothieware:http://smoothieware.org/ . Rostock MAX config file for Azteeg X5 Mini:http://forum.seemecnc.com/viewtopic.php?f=35&t=5537&p=44293#p44293 ....

Faceplate and mount for azteeg x5 mini v3. I don't have wifi version but just slight modifications to faceplate may make it work. Faceplate mounted with 4 M4x8 button head screws and mount with 2 M5x8 socket head screws. Azteeg is held by faceplate...

This is a control box for the Azteeg X5 GT designed in the same fashion as the stock Voron RAMPs box. There is a hole for a pin for the lid that is just big enough for a 1.75mm piece of filament to fit to use as the Hinge. I've also attached the f3d...

This is a mount for an azteeg x5 mini for openbuilds 40mm vslot extrusion (2040 or 4040). Use m5x10mm screws to attach to extrusion. Use m3 x 12mm to attach board to mount. (In the photos, I used arduino washers and m3 x 16mm) 9/3/2016 - rev 1.5 -...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/4wUwnDotw80

Was looking for a clean way to mount my Azteeg mini into my Kossel Mini while still being able to access the USB port and SD card.Allows for use of the heat sink under the board, and electronics cooling fan.Fan intake draws near one motor and exhaust...

Was looking for a clean way to mount my Azteeg mini into my Kossel Mini while still being able to access the USB port and SD card. Allows for use of the heat sink under the board, and electronics cooling fan. Fan intake draws near one motor and...

... for a 90mm fan, which would be mounted diagonally. "Azteeg_X5_GT_Mount_Frame_IT2_-_Corner_Mount_Holes.STL" has fan brackets, but also 4 mounting holes, so that it can be secured to a panel or whatever works for you. ... Pictures to follow...

This is a simple enclosure for a [Azteeg X5 mini smoothieboard stepper controller board](http://www.panucatt.com/azteeg_X5_mini_reprap_3d_printer_controller_p/ax5mini.htm) from panucatt. I designed this for my Makergear M2 printer to replace a broken...

... starting to print). The board is mounted with the bottom of the PCB looking upwards, this way the 50mm X 10mm 12V fan can cool the stepper drivers much better (the heatsink coming with the Azteeg X5 mini board is mounted on the bottom of the PCB).

This is either a 1 piece or a 2 piece Panucatt Azteeg X5 GT mount. I had trouble printing with some old ABS lifting so i made a 2 piece style also. Cooling fan used.

... ...This gives much easier access to the wires. There are separate versions for the Azteeg X5 Mini v1 and v2/v3. Also included is a 60 mm fan mount for cooling the board. This is important. The Azteeg likes to get hot. ... Solidworks Design Files

This is an enclosure for an Azteeg x5 mini v2, has cutouts for all buttons, terminals, the USB port, and sd card port. The top has cutouts for all of the stepper, thermistor, and endstop pins, as well as zip tie tie down points for all cables. ... It...

There is also a built in mount for the Azteeg X5 board which hangs on the bottom. This keeps it nicely tucked out of the way and makes for easy wiring. With the included cable, the Viki mount can only be used from a distance of about 15" from the...