azteeg 3d models
123 3d models found related to azteeg.thingiverse
A tray to hold the Azteeg X5 Mini, allows cooling to run under board, and leaves sides and top clear for wiring. Board should just snap on. ... Added tabs to allow attaching to extrusion.
thingiverse
Azteeg X5 V2 Mount. Mounts on 20mm V-slot Tap holes or enlarge for 3m screws. ...Print Settings Printer Brand: LulzBot Printer: ...
thingiverse
This is a case that the Azteeg X5 Mini will fit into, making it easy to not accidentally have a short circuit, and of course to organise all the wires.
thingiverse
This is a VERY rough sketch of the Azteeg V2 with an SD card made in Fusion 360 for custom enclosure making. ... It probably matches up with the V3, but the ethernet port is not modeled on this one.
thingiverse
The box is for Viki LCD with a Azteeg X3 Controller Instructions Print out all the parts Thread All 2.5mm holes with 3mm tap Fasten together Enjoy I have attached a step file in case you want to do any changes
thingiverse
This is a mounting bracket for the Azteeg X3 controller board. It allows for chassis mounting horizontally or vertically with M5 bolts. The board mounts to bracket with M3x0.5 screws. ...Version 2 Adjusted some heights posts to clear board components ...
pinshape
SummaryThis is designed to place the Azteeg X5 Mini with the usb connector close to the outside of a kossel vslot 2020 based printer. I've added a central bar to make it less flexable, and also added m5 mounting holes. ...I put the standoffs on the...
thingiverse
This is a case with integrated 60mm fan mount for the Azteeg X3. It can only be used with the soldered screw terminals, but I have included the SLDRPT files if you want to modify it yourself. ... There are some pretty large bridges here so make sure...
thingiverse
This is designed to place the Azteeg X5 Mini with the usb connector close to the outside of a kossel vslot 2020 based printer. I've added a central bar to make it less flexable, and also added m5 mounting holes. ...I put the standoffs on the outside,...
thingiverse
I got tired of looking at my Azteeg X3 sitting on the desk next to my printer so I took sgraber's mounting plate, nischi's rail clips and melded them together to create a mount. The mount fits around the rails on my MendelMax and has nischi's clips...
thingiverse
Hinged mount for Panucatt Azteeg X3.Latch is a work in progress but the hole in the tab will alow a screw to hold it in the closed position. Instructions As of now I do not have the latch worked...
thingiverse
An enclosure for the Panucatt Azteeg X3 to fit on the Prusa i3 or Prusa i3 Rework frame. It fits a 50 mm fan for board cooling with intakes on the bottom of the box. the lid is snap on with slots for the mounting hardware, fan, and a slot on the...
prusaprinters
An enclosure for the Panucatt Azteeg X3 to fit on the Prusa i3 or Prusa i3 Rework frame. It fits a 50 mm fan for board cooling with intakes on the bottom of the box. the lid is snap on with slots for the mounting hardware, fan, and a slot on the...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=166045 This bracket should fix the Azteeg X3, allowing the fitting of a 40mm cooling fan. The idea came after I burned my finger on a stepper driver board. The fan can be driven by the extension...
thingiverse
Modeled up a Azteeg X3 standard controller box. I haven't printed to test it yet but will once I finish my upgrade I will. Tired of seeing all the wires so I'm hoping this box will help me organize some of the wires inside the box a little and then...
thingiverse
mount for the azteeg x5 mini v3 optimized for the kossel pro (15mm extrusions using m3 hardware)
thingiverse
Really basic Azteeg X5 GT mount designed for the corner of the Voron printer(2020 Extrusion). ...Plastic standoffs were used to connect the controller to the mount.
thingiverse
I wanted to keep this Rumba case so I modified it win Fusion360 to fit the Azteeg X5 mini V2. Also added a slot below board to allow my wires to enter from between my horizontal extrusions. ...Update 5/19/16 Removed a few old standoffs and tidy up...
thingiverse
I originally printed this for a Rumba board but switched to a Azteeg Mini V2 32bit and wanted to keep the same setup so I modified the back case in Fusion360 to fit the Azteeg. ...This is a really nice design by e-nozzel.
thingiverse
Box that I re-lofted to accommodate the Azteeg mini X5 V2. I like the design of the source box but just didn't fit the V2. R01 changes the size of the card slot and usb. (was a bit too small when I printed mine. Print Settings Printer Brand: ...
thingiverse
This is a mounting clip for an Azteeg X3 and designed to slot into the center channel of an OpenBeam extrusion. The center hole is sized for an M3 x 8mm cap head screw. Secure with a DIN934 M3 nut inserted into the extrusion slot. The is a...
thingiverse
This is an Azteeg X5 mini v1.0 mount that I designed for my kossel mini.
thingiverse
This is a simple bracket mount for the Azteeg X3 Pro. The fan is a 92mm. ... Have fun!
thingiverse
... Done. I made this after seeing the "Sanguinololu adapter for RAMPS mounting holes" by Sound: http://www.thingiverse.com/thing:39893. NOTE: The Azteeg X3 board hole spacing was obtained from http://files.panucatt.com/datasheets/x3_wiring_diagram.pdf
thingiverse
Support for AZTEEG X3 PRO on voron 1.6 and 2.x 4 Square nut 4 M3 srews 4 2020 m5 tnut 4 M5 x 10 screws
thingiverse
May work for other versions of the Azteeg X5 Mini but I only have version 3 so I can't confirm. ...Print Settings Rafts: Doesn't Matter ...
thingiverse
This is a simple mounting plate for an Azteeg Mini X5 V2 to be used on my mini-Kossel (with 2020 rails). ... Print Settings Printer: Mini-Kossel ...