balun box 3d models

I made this to house a 4:1 /9:1 / 16:1 Balun and suspend a wire antenna for ameteur radio use But could be used for many uses

This thing was made with Tinkercad. Fixed file has all the components aligned on the bottom. ...Was created when I was still learning and I never noticed the small alignment problem.

This is a Current Balun box that fits a T140 toroid wrapped with 22awg PTFE wire. (Edit 3/24/23 SO239 Bolt on box updated with more robust mount points) To build this out you will need the following additional gear items 4x 22awg PTFE wire (each one...

Also its a practical quick and stronk box to put your junk in.. But not that junk.. If that junk fit.. Then well anyways.. Download and print if you want. Holds together with a few bolts, or you could always use flex seal or whatever cool sexy...

a wind storm broke the long wire antenna I used, in taking down the balun I notice the inner cylinder came off the bottom...so I made a sturdier design that tapered the bottom....this one (version 1.1) should not have that issue after doing one long...

This is an unun/balun box used for amateur radio or shortwave listening. There's a lid and seal too, but you may not need the seal unless you plan to print it in something like NinjaFlex to use the box outside. It's designed to house a FT240-43...

Only a box to save balun or unun

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/l9kltvHaVTf

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/gZVQn93VP2r

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/bROD4K6gdHy

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/eJTkr3ZaFJE

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/gMUrx0MkSpY

... When customizing please adjust boom_width and boom_height for boom dimensions box_x, box_y, box_h for balun box dimensions When adjustin box_x dimens, please also adjust dipole_offset_l, and dipole_offset_r folded_dipole_r for folded dipole radius.

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/kpyHUQtFJat

Customized version of https://www.thingiverse.com/thing:1680291 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1680291

As my Ham Radio hobby has expanded I have made more baluns....in need of a enclosure to house my 240 type 43 I made the following ...enjoy!! Should fit all 240 size torroid rings....I have a hole made for the so-239 and main wire...I don't need a...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/1XgbxYaIaLN Derived from https://www.thingiverse.com/thing:845444

Update: - Box für 1:1 Balun hinzugefügt - Box für 4:9:16 Balun hinzugefügt Anstelle der Bananen-Buchsen können auch M6 Schrauben verwendet werden. Box für UNUN (BALUN) 1:49 für AMI FT-140-43 Ferrit-Ringkerne, Material 43, für Ø22,9 mm. ... 1 Stück ...

I needed a box to enclose a DIY 9:1 Magnetic Longwire UNIN wound onto a T200-2 toroid, so came up with this. ...The base has a single countersunk hole to allow it to be screwed down to something.

T140 & T240 versions Case for making a portable balun/unun matching transformer capable of 100w when made with the below components. FT140-43 FAIR-RITE FERRITE CORE TOROID RING ...

This is dipole centre box with space for ferrite balun. This project is in development. ...In near future i will add isolators, 20m trap carcass and all info how to set up dual bender dipole.

Balun case

Balun Antenna Dipole

This is a small balun box and dipole support to build a dipole antenna (or end fed wire) Parts required: 1. UG-290/U panel mount BNC connector 2. Quantity 8 of M3x30mm bolts 3. Quantity 8 of M3 nuts 4. Quantity 4 of M2x10mm (or 8mm) bolts...

Simple case for balun for dipole center with SMA and 1:9 balun. Use super glue to assembly case. ... https://nl.aliexpress.com/item/32972573085.html?spm=a2g0s.9042311.0.0.1ec64c4d60JNwN

Case for 4chanel dvr baluns (turn out a litle bit tight.. ...but works fine) Update: Added a V2, best fit, less plastic

This little box will hold the NooElec Antenna Balun 1:9 HF Balun to protect it. https://www.amazon.com/NooElec-Balun-One-Nine-Applications/dp/B00R09WHT6 Print Settings Printer Brand: Robo 3D Rafts: No Supports: No Resolution: .06 Infill: 100 % Notes:...

universal cover for QRP unun/balun

Balun-Case print in PLA without Support. Stopfen in TPU. Use an BNC Connector for the Balun. ... I use this Balun Case for my 9:1unun.

Holds two baluns for biconical antennas for shipping or transporting. ...