baofeng uv5r case 3d models
222683 3d models found related to baofeng uv5r case.
thingiverse
Designed this stand cause after changing the stock antenna to a better/longer one gifted to me by my bf the radio could easily fall over and probably brake so i made us 2 of these! It doesn't hold tight on the radio and that means you just lift...
thingiverse
This is a custom clip designed to securely hold 5mm wide contacts onto the battery of a handheld two-way radio. Note: The contacts must be quad-A or triple-A sized, as larger AA-sized contacts are too wide to fit onto radio battery terminals. To...
prusaprinters
<p>Original loop have sharp edges and useless for me so i made this replacement. ...Trim with knife if need it.</p>
thingiverse
A simple antenna holder that slides on to the belt clip for the UV-5R to reduce the vertical profile. ...good for travel or just keeping the radio in your pocket without worrying about the antenna.
thingiverse
Modified to fit the center vent of a Grand Caravan 2011, fit perfectly!Printed in ABS
prusaprinters
<p>I have the same problem as most with the UV-5R. If you move the headset plug slightly, the radio will no longer work.<br/> There is already a solution for this here. ...However, I didn't like it because it is too bulky and you have to buy...
thingiverse
While there is quite a lot of overhang underneath the knob, its so small that support material is not too big a challenge.
thingiverse
A very simple mount for my handheld radio. The bar is 22 mm - but as it is fixed with zip-ties, other diameters should word as well. I glued some foamed rubber on the surface for a better grip. May I try to print in with flexible filament to absorb...
thingiverse
Inserting the belt clip requires positioning it within the top portion of the device, which serves as a secure location for storing items like headphones or other accessories.
thingiverse
Customized version of https://www.thingiverse.com/thing:5277569 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5277569
thingiverse
I have the same problem as most with the UV-5R. If you move the headset plug slightly, the radio will no longer work. There is already a solution for this here. However, I didn't like it because it is too bulky and you have to buy screws. The...
thingiverse
The BFoxCon is designed to seamlessly attach to the Baofeng UV5R in place of its belt clip, creating a sleek and integrated look. The custom case I have printed proudly displays my callsign on its exterior. However, understanding that others might...
grabcad
You can change this design according to your needsThis case uses a magnet with dimensions of 8mmx2mmpins on hinges can use filament with a diameter of 1.75mm
thingiverse
Here are your printing options for this customizable iPhone case: Using the following settings: - Pattern shape: hexagon - Pattern radius: 8 mm - Build plate selection: top layer - Pattern thickness: 2.5 mm - iPhone model selection: latest model...
thingiverse
Designed this to keep from knocking over the containers of media and graphite of Highline Precision case neck lube. updated a and fixed size problems with openings. ...1-14-2023
thingiverse
The boards looked identical at first glance, but upon closer inspection, there were differences in component placement and mounting, as I discovered after printing 2 cases.\r\n\r\nIf one of these cases doesn't fit your device, try looking at the...
prusaprinters
Советую сделать "нечеткую оболочку" на внешних стенках (кроме замковой части).A very simple case (tube) for brushes (or anything else). It consists of two halves with a simple latch. ...I advise you to make a "fuzzy shell" on the outer walls (except for...
thingiverse
... To customize your build, set these options: build_plate_selector = 0, pattern_shape = 9, case_thickness = 2.4, pattern_rotation = 180, pattern_overlap = 6, pattern_radius = 22, pattern_thickness = 14 and iphone_version = 2.
thingiverse
This modification allows them to keep the waterproof feature of the original case while changing the screw orientation. I'm currently refining the fit, which is nearly there but not quite meeting my expectations. Update: After making some...
prusaprinters
Советую сделать "нечеткую оболочку" на внешних стенках (кроме замковой части).A very simple case (tube) for brushes (or anything else). It consists of two halves with a simple latch. ...I advise you to make a "fuzzy shell" on the outer walls (except for...
thingiverse
... I just glues the collars on the left into place. Once assembled I have a zip tie strung across the top putting downward pressure so that the Digitakt presses into the lip of the case, this keeps it from falling out when turned upside down. ...
prusaprinters
The boards look the same, however the component placement and mounting was a little different (as I found after printing 2 cases...) If one of these doesn't fit, take at look at the others, you may find one that fits your device. Print...