basilisk model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Legal notes 3D printable file and model ©2021 Bethesda Softworks LLC, a ZeniMax Media company. All Rights Reserved. ... STL files are sold on an "as-is" basis only, we do not accept modification requests and printing and technical support is not...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

The diameter is 50mm, 23 teeth, pitch 2, height 20, slop .01.Updated threads were created using Fusion 360 and then incorporated into the Tinkercad models.  Several versions were tested at various tolerances to get just the right fit across...

More information: The models were printed in PetG and have a consumption between 5.7g and 7.0g and the printing times range from 0:47 to 1:15 hour. Note1: If the z selection alignment is used, you can generate a line as the one shown in the...

Then, once the mount is installed on the handle, you can unscrew the bolt and increase the distance from the magnit to the sensor, increasing it enough so that the brake sensor only activates when the brake is actually applied.The model is made in...

I changed the position of the threaded inserts and added additional to replace the hex nuts. Modified the cable paths and tie wrap holes for easier printing, and thickened up some sections to print better. Modified how the front and rear clamp...

Another thing to note is that there have been a few minor changes to the model since I printed the one in the pic, however I don't think anything changed will cause a problem. The STP file is included for remixing. Just wanted to mention some info...

Do a full render to see the models properly. ## Printing Print 0.16mm regular black PLA. I use a XVICO X3S - very cheap printer. ## Cassette Lid The lid is rendered the "wrong" way around. This is because it is easier to flip it on...

There you can find links and reviews about quality hobby products. https://MyHobbyTools.com ✔ 3D PRINTING My Favorite 3D Printers 3D Printing Tools 3D Printer Parts ✔ ELECTRONICS Batteries and Chargers Soldering Kits & Modules Multimeters...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

The 3D model in the pictures are from a Creality Ender 3 and have adapted the necessary dimensions for this project to my Creality Ender 3 pro. When removing the support, I always first pierced the edge between the support and the part with the...

 On my ESC I have to start with the minimum setting (effectively the throttle channel on an RC model), which I believe is a great safety feature.  BTW you can also program your ESC using the knob as if it was a throttle control, if your device...

Great model from Revennant. Remixed to no base and support free again. https://youtu.be/O5-rbg4MrVg <iframe width="560" height="315" src="https://www.youtube.com/embed/O5-rbg4MrVg" frameborder="0" allow="accelerometer; autoplay;...

My goals for this project were to model everything with the least amount of material waste (support material) needed and that everything is easibly printable. What you need to print: 1x air.stl, 15%-20% infill, support on built plate only (I suggest...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_left_port_length = 50 custom_top_port_corner_radius = 5 pattern_element_rotation = 0...

This design models elliptical propeller blades that transition smoothly through three different NACA airfoils, starting with (by default) NACA 8430 at the hub radius, transitioning to NACA 6412 at 33% of the blade length, ending with NACA 3412 at...

In my models are embossed labels A, B and C for easier assembly.&nbsp;Length A is 350 mm and you will need 30 piecesLength B is 398 mm and you will need 44 pieces (45 if you want full dome without entrance)Length C is 500 mm and you will need 10...

There is a tight-thread version of all the models for those wanting a tighter fit or using a resin printer. Caps Flat Cap Flat Cap with GB Logo Cap with 3/4" Loom Stub Cap with 3/4" Loom Stub and Circuit Passthrough Cap with GX-20 Geometry Cap with...

I always wanted to design and print a swamp boat. Now it was time to realize it. The boat consists of two parts, which are screwed together. For sealing the whole thing is glued around the internal cable duct. I took the motor and ESC out of my MHQ...

Note that the earlier XT (and other Zumo models) have a 12 volt to 5 volt conversion, so as far as I know this will only work with the XT2 mount (which has a slightly different pin layout from the other Garmin mounts)I have not tested the Carpuride...

This model only cost 1 dollar because I am only pricing the topper and Star mount, the rest is free with the purchase. This is a pixel tree mount to build an eighteen string 216 degree pixels tree. Height can be up to 5 feet. The base design is...

Future models could have built in cable management. There is a space in the box for mounting the arduino pro micro and also the MCP23017 I/O expander. The buttons are wired as a 4 x 10 matrix to give the 40 buttons so 14 pins are needed (hence...

You can fit dividers in any space, and they fit next to each other too if necessary, but you probably don't want to fit one in the front space as it will block the finger hole in the front of the drawer.If you make one of these, please post your...

the better the less likely it will grab but u can always use nuts on the other side even tho i didnt make a place for them to sit on the model since i had planned on using the threaded inserts but it will still work cause thats how i test fit...

... to be able to modify the z offset.</p> <p>Printing ABS in the air provides a clean and even bottom. The support is catching and holding the hot air from the bed under the model, so there is no lifting or bending. Category: 3D Printer Accessories

Some models are remixes but mainly are made from scratch. affiliated Tools used to build the motion simulator: IWS-2820M Crimp Tool (good one): https://es.aliexpress.com/item/4000073000826.html Small usefull wire stripper:...

Keep doing it until you get a reliable contact. Multi-color printing For printing in multiple colors, you need to slice the model and save it as normal gcode. Then, you have to insert the M600 command. You can do this manually by opening the gcode,...

Lightweight PLA tool is non-conductive, non marking and wont damage your materials if dropped the same as a heavy chunk of aluminum will.&nbsp;&nbsp;Files Grouped in 5 Categories:MK3S+ Gcode Pre-Sliced - combined : All Files to build everything pre...