batmobile model

Test Print Video here: https://www.youtube.com/watch?v=H8vL2GeMYMQ Previous version here: https://www.thingiverse.com/thing:4650517 As per the previous version a big shout out to Scott3D for his fabulous work on the Hypercube Evo which I have taken...

A few copies of it will be printed, for two reasons: cooling during print and as spare if some print fails. raketplattform överdel_xy0.4mm_z0.2mm_ELIXIR_ELIXIR_ELIXIR_ELIXIR_ELIXIR.3mf raketplattform...

Z gap between support interface and model is 0.2 mm For the adapter plate I used standard supports with the same support options Other parts: For convenience, I included the 40 mm fan cap, part cooling duct and BLTouch mount from the original...

I have not modeled any nut traps in the parts because I think they will weaken them so all bolts here just screw into the plastic. I believe the parts are thick enough that the bolts will not loosen but time will tell._ 1. Completely disassemble...

Specifically, the mouth utilizes inexact measurements, and inconsistencies in source models from the 3D printing process made it difficult to gain a good measurement. On the sketch, we measured the mouth to be 1.20cm from the side of the constraint...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

Do not purchase unless spare parts are easy to get; not all parts are easy to CAD model or print. OEM replacement parts for the q905 can be found [here](https://www.hosim.com/collections/parts-for-q903).You can also take the OEM part number and...

I have completed the task, which is an intricate and comprehensive model. It required two full weeks of my time. I eagerly anticipate your appreciation for it; have a great day! :) :)</s> щ поставих задачата, която е детайлна и обширна конструкция. Я...

The automatic transmission in some models has a tendency to fail prematurely. This usually happens around an average mileage of 108,000. **1.1 Identifying Transmission Issues** Transmission failure can be determined through comprehensive...

This has taken several months to work out the kinks, but I think I have a good working model now. However, here are a few things to note: Prior to any assembling of any of the parts, I have found it is best to pre-thread all of the screw holes...

I checked with Meshmixer and the model is fine. Tried re-exporting from F360 to a new file and experienced the same issue. I opened a bug report, but Ultimaker closed it as not being able to duplicate.</strong></p> <hr/> <p>The case is designed to be...

I 3D modelled and printed some end caps for it with Ninjaflex so it doesn't scuff up my walls. 4/10 update: I added some parts that hold a 3/8" steel rod in the middle of the pull up bar so it isn't just relying on the screw coupler to hold the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Wandering hour clocks have been around since the 1600s, but this one implements the concept in 3D printing!This example uses the case, dial pan, glass, and movement from an IKEA BONDIS, but the model could be scaled on the X/Y axes to fit almost any...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 74 printer_tolerance = 0.4...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 120-277V and 347V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring: These LED light...

The solution is simple enough: Both parts of the model need to be placed away from the centre point (still properly lined up with one another, obviously), so that the probe can do its thing without the first print getting in the way. So began attempt...

This seems to be a weak point in all reciprocating saws and is a particular problem with this model, with some users reporting that the blade clamp had sheared off after only relatively light work. Replacement parts are available, but at a...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 120-277V and 347V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring: These LED light...

The shoe lace is optional but it's a good way to secure the handle from unfolding when you don't use it.Print SettingsDon't rotate the models when placing them in your slicer. I have placed the parts in the best orientation possible with surface...

The attached model is sized to fit the Eye Cu Smile V2 and V1 filter housings at 45 mm OD and 10.5mm high However if you want to make any size antimicrobial / antiviral filter meshes for any purpose then even sketchup will suffice Steps to draw a...

... and presupported version. This product contains the following parts: 32mm Base 40mm Base Balthazar Morris DnD 5E Datasheet Get a 40% discount on this model by joining my Patreon! You can also order physical copies at my shop on Only-games! ...  

This model is intended to be glued together using Gloop! Get your Gloop! here: </strong><a href="https://3dgloop.com/shop"><strong>https://3dgloop.com/shop</strong></a></p><p>Assembly made without using Gloop! may result in the need to prepare for...

The retainer is up higher than need be in the video for safety.--------------------------------------------------------------------------------------------------------------All parts printed in PETG, with standard Voron settings for rigidity.0.20...

Remember to check the wiring of your relay if you use a different model or brand. Adjustments If you set the microswitch to click when the bed is at Y=220, then it will work out of the box with Cura. I still recommend you to modify you G-code to...

Happy soldering! Source Files This print was modelled in Onshape. You can access the source files from here:</p> <ul> <li><a...

On the bottom of the print there is a text saying “Valentine 2022”.&nbsp;In case a name you need is missing, you can customize the model to show it: Please install OpenSCAD on your own computer and follow these instructions.If you could take a...

They should easily fit even on small printers; if you can print Hadley, you can print this mount.The mount uses a vinyl disk that sits on top of teflon pads, for very smooth motion.It is very lightweight, and can easily disassembled for compact...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...