bed leveling test pattern 3d models

Compatibility I have only tested this with the following configuration: * Creality Ender 5/Pro * MicroSwiss Hotend (the mounts are the same for the stock hotend, but the blower scoops may not be quite right) * Printermods MDD Direct Drive Kit * Dual...

Made in solidmade, tested in the manufacture of the master model of the product. Saving stl & obj files occurs at the average values of polygons. This is usually enough to print a model in a 3D printer, but it may not be enough when producing a...

I added a button for manual activation but mainly used it during the testing phase, and I'd maybe keep it for occasional bugs where the device doesn't perform exactly as expected.\r\n\r\n**One important thing to note is that the servo will draw quite...

Origional model http://www.thingiverse.com/thing:2105057 EZ Print model https://www.thingiverse.com/thing:2153317 Mounting Base For Testing http://www.thingiverse.com/thing:2154052 Use the origional model for attachment to the mounting base, the EZ...

If you cut around the ears, the effect is less impressive (at least in my tests it was). 8. Depending on the model and the haircut you may want to cut a bit of the Hair (horizontaly) on top and reduce the mesh count again. 9. Export as STL ...

I only played Jaws of the Lion and do not have a copy of the board game, therefore the prints are not tested on Gloomhaven/Frosthaven, but I assume they might work (e.g. is the card board the same thickness ~2 mm?) The system contains the...

While I did this project to test my 3D printer and challenge my skills using it, you don't have to make this with a 3D printer. It could be made from cardboard, Styrofoam, Balsa wood, or any lightweight craft materials. Be creative! How else can you...

Tested Gear Ratio when driving small planet gear and discovered it is 49.something:1 but cannot figure out the math behind it. Comment if you can answer. 1/29/17 - Designed a Mini Version! Check it out! http://www.thingiverse.com/thing:2071318 ...

I highly recommend to print the blades 100% solid as they are the weakest parts of the thing anyway (set 6 walls/perimeters, this should be enough to avoid infill inside the blades).Other settings that I used: PETG 240/70, 0.4 nozzle, 0.4 width, 0.2...

have not actually tested it. All the speaker holes are clear, too. Will update with pictures later. * 07-05-18 - Update - Added sides I volunteered to help SAG a road race at Gillette Stadium, and needed something fast to help shore up my phone. I...

Do some tests to find your preferred rubber bands. The number/ strength of the rubber bands will directly affect the power of the gun but also how hard it is to pull the trigger. When you're happy with your rubber band setup, install the...

The supports have only been tested using .2mm layers but 'should' work with smaller layer heights. The supports come off in four parts. Do not use a knife to remove the supports. *The optional part, hair_without_supports, is positioned for slicer...

Test this on a few different prints to find your perfect settings.AssemblyParts are designed to fit M3 bolts/nuts (or brass inserts) - which is 1/8" bolts/nuts for the USA.All parts should line up and be easily assembled.Printing ball joint parts in...

To do this, adjust the vertical axis with a test print with "Horizontal expansion" and "Horizontal hole expansion". The 8 mm rod must sit tight in the vertical holder, the VertikalHalter16x8 fits on a 16 mm rod / tube. VertikalHalter0Z5x8 fits a 1/2"...

Printed quickly (here already 2h printing time) to test it. Even already in the wild. And it worked.</p><p><br>Version 3 can be seen here in the pictures. I use this version actively and actually everything fits. ...But there is always room for...

Therefore, I have modeled them all to be slightly on the loose side (each puzzle had to be individually tested due to differences in fit). If you want to try printing them tighter, you can print the "`tighter`" variants instead...

Alternatively, I am posting my specific parts list here: * lamp socket: https://lightstock.de/fassungen/bakelit-lampenfassung-e27-mit-schalter-teilgewindemantel-schwarz-mit-zugentlastung/ * Threaded tube:...

I also ran my earlier tests using gyroid infill, which I understand was a mistake vs cubic infill or the like to try to minimise flex.I managed to run the hammer at:2 layer walls/15% infill using stock spring3 layer walls/15% infill using stock...

Made in solidmade, tested in the manufacture of the master model of the product. Saving stl & obj files occurs at the average values of polygons. This is usually enough to print a model in a 3D printer, but it may not be enough when producing a...

tap on the screen. The FreeCAD file still includes the earlier "rounded" version with brackets that tried to match the contour of my phone very closely, with extra cutouts for not pressing any switches on the phone's edges. ### Material Use PETG for...

I'm guessing for the larger prints, it's best to use supports, but maybe I need to test some more. I'm pleased with the model, I think it captures the essence of Bender better than the other model, but it may come at a price. RECAP (edit): You...

The JET version is already in testing! https://www.youtube.com/watch?time_continue=1&v=wE5t6pLmP8I Here's a little clip of driving the boat.. Fins are not installed yet! New video will come soon. Hi, this is the remake of a boat my teacher...

Made in Solidmade, tested in the manufacture of the master model of the product. Saving STL & OBJ files occurs at the average values of polygons. This is usually enough to print a model in a 3D printer, but it may not be enough when producing a...

As the pump needs 3V as input, a small step-down converter is included in the design, so that the usual fischertechnik 9V (or anything between 6V and 23V) can be used. In my tests, the pump provided up to ca. .7 bar at ca. 3.5V input. Due to its size...

At this point, if you've got a longer rubber band, just wrap the extra length a few times around the body of the lock.Test your lock by inserting the key as shown and turning it. ...A drop of oil in the gap between the back piece and the lock face...

UPDATE 03MAR18: Collar reinforcement V4.5 In my recent tests the collar performed well. I printed a large batch of 40 last night and noticed the collars were separating from the bases (using PETG). It may just be that my printer needed to be...

A great source for such chips are web cams - because you can pick one that is supported by recent OS and you can test it beforehand to see how it looks. You practically need just the iside PCB with the CMOS chip, no lenses, as we will reuse the...

The filter housing in particular isn't that easy to print even if your printer isn't falling apart, it's basically a overhang, bridging and retraction torture test, so take it slow and make sure everything is tuned or it may fail. The filter...

Made in solidmade, tested in the manufacture of the master model of the product. Saving stl & obj files occurs at the average values of polygons. This is usually enough to print a model in a 3D printer, but it may not be enough when producing a...

I will extensively test this over the next few weeks, if improvements are needed or you have suggestions please leave a comment. For sure I will rework the rear anchors design (they do not rotate 100% along the same arc as the arms). UPDATES:...