begode t4 3d models

Lamp protection for Begode t4. ...Not my model

My fix for handle of Begode T4 so it will be hold on tight

5mm thick armor cladding for the Begode T4 battery boxes. Fit is precise. Mirror top on X-axis to get both sides. Works in companion with my other T4 print. https://www.thingiverse.com/thing:5563862 Use filament of your choice. ... Can be...

Remixed the Veteran Sherman stand to fit the Begode T4. I widened the width for easy roll in and added bumpers which should be printed in TPU. You will have to glue them in together. You can print them in PLA if you do not want to use TPU. In that...

Begode T4 Fairing, Front Bumper and Back Handle There is really no need to explain the purpose of a fairing system for the Begode T4. You will fin the files for the side fairings, the front handle/bumper and the back handle/suspension protection. ...

I call it the Titan Armor for the Begode T4. Since the original master Titan Armor does not allow remix, you will have to grab the nose and tail grip from that listing: https://www.thingiverse.com/thing:5453902 Also, please grab the master riding...

Bumper holder for EUC Begode T4

Right spacers for begode T4 for bearing protection. ...Differ in the diameter of the outer circle

Relocates the T4 mudguard to position, where it actually protects the shock. ... Attached with velcro tape

Front/rear battery protection for T4, may be suitable for the master. ...As easy to print as possible, to get the desired length, you need to scale the model along the x axis in the slicer by disabling unifirm scaling.

Frontal protection and stand in one. ... In addition, it looks cute. Works in companion to my other T4 print. https://www.thingiverse.com/thing:5623749 Print the Head with TPU and the Nubbins with the material of your choosing. ...

Additionnal Pad for Begode T4 kick stand. You will need 4x screws (M4 16 mm). ... The wheel is much more stable with this print.

Begode T4 Back Handle & Suspension Protection This handle will fit on the wheel with stock pads (you will most likely need to cut the back pad a little bit) and my fairing system. This is my take on a back handle and suspension protection for the...

As soon as I got my T4 I knew that the trolley arms would be an issue with the amount of SLOP they had. Its like Begode realised the problem and called another mfg. ...guy over the phone and vaguely described the issue to him with vague measurements and...

when the steering wheel leans forward... pull the handle use saddle bolts 50mm between two bolts.. I don't know if it works with master pla or nylon, petg, asa... ...but the best is flexible TPU I use 70A hard TPU, and it doesn't break and is...

Reposition the stock mudguard, so it actually protects the shock from debris, Attached with velcro tape.

My very first ride I grabbed at the rear and pulled the seat up. That was annoying. This Seat Pin secures the seat much better than before. I do not notice when riding seated. Print with TPU. I used a .6 nozzle and 6 vertical shells. ... ...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/kyy5V7SIr9O

Protection of the bottom of the batteries and the rack. Fits snugly on the battery bracket. ...You can simply glue it or fasten with m4 bolts

A simple mudguard, attached to a double-sided tape or similar. ...The mudguard has a nuance, and in the lower position of the suspension, the rear lights can tear it off if they are installed at an angle inward, they must be fixed in the position as in...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/fV3QAGQSq5h

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/kyy5V7SIr9O

I wanted something sort of classic looking, but still blocky and bold to match the T4 and Master design. The mount plates are nice and strong and the fender can be attached using the original mudguard 4mm screws. If I get enough requests, I'll...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/3Sh3fWk6XAO

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/6df5f5hty7q

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/a3CDcGfFmHq

Not an actual remix, just the fixed version of the original .stl file from the original project.

This is for the QS motor not ZX which is below https://www.thingiverse.com/thing:5850143

... problem! This mini handle is designed so that you can lift your Master or T4 by the back without a hug back handle/bumper, and it hides the screws that stick through the seat. ... I printed in PLA+ with 4 walls and 25% fill, and it works well.

Адаптер для манжеты 60x80x8 (сальника) подшипника. для мотора ZX. для мотора QS может не подойти, не могу проверить. Манжета в переходник и переходник в крышку колеса вставляется очень туго, возможно придется подточить, в зависимости от пластика и...