bike light holder 3d models

... I did. ... Instructions this is for a low voltage halogen bike light, to mount to handlebars, don't know who else night need it but thought I would share it just in case, printed with makerbot 1.75mm black ABS, layer thickness 0.2mm, solid and normal

Designed for the Mountain Equipment Co-Op (like REI but Canadian) "Plasma" LED Rear Light , but really should work with any bike light designed to attach to a seatpost. ... The intent of the adapter is to allow you to attach such a light to a 20mm...

I made this mount to attach my bike light to my bike stem, and free up space on the handlebars. The light clips into the round end of the long piece which is bolted to the u shaped piece which is "rubber banded" to the stem. So Additionally to these...

This light bracket has been modified to fit a bike light less snug than originally. Mounts to the top of the deck via truck screws keeping the light more protected. printed with PLA 100% infill for the upmost durability! no supports. X2 M3 screws...

This is a small cap for bike light buttons. As I put the light in my pocket, the button sometimes is pressed and the batteries drain, leaving me with an empty light in inconvenient moments. This cap prevents switching it on by accident, with just...

You'll need the original screw from the bike light to attach the parts on the top and can then use two M3 screws and nuts to secure the clip around the handle. ... If you want to see what else I do, you can check out my website: ...

I wanted to make a little throw ball for my nephew that blinks/lights up. ...So I took apart a little flashing bike light and measured out a hole in tinkercad that would hold it. ...I also added holes for a rubber band to keep the 2 parts together.

The holding part of my bike back-light broke so create a new one. Needs to be glued on the actual light. ...Print Settings Printer: UNI-PRINT-3D ...

Hi, this is a Bike Light Mount for a unibranded LED Bikelight from Aliexpress, Gearbest, Amazon, .... Geodash 3x LED Bike Light The light should be waterproof, but for that reason you should close the threaded hole on the bottom side with a eg. ...(But...

This is a handle bar mount for a quick-release attached bike light. (Mine is a light & motion light that has a particular mount) Instructions Modify the quick release insert for whatever you have. I did this in openscad. ...You can use the instructions...

This light is designed for my ebike, it runs from main battery. I used 5v LED strip, you can run it on 3x AAA or AA batteries. Enjoy ! Added new file with easy print glass. ... As promised here is battery powered version: ...

Parametric Bike light housing for the cheap chinese models which are found here: https://www.amazon.de/DKINs-Fahrradlicht-Wiederaufladbare-Fahrradleuchte-Wasserdicht/dp/B07WZPTDWZ/ref=cts_sp_2_vtp The mounting hook broke and I desiged the new housing...

This was designed to integrate a Lezyne Femto Drive front light direcly into a 10mm spacer, which are commonly used on bikes. Just replace an existing 10mm spacer with this adapter and off you go! Its watersealed (remember to put the O-ring on!)...

This Inspired Bike light luggage rack was brazed together from copper tubing, brass tubing and copper fittings and bolted to the underside of the seat cover of the R1100S. So you can remove the cover at any time. ...Constructed in Inventor 2017

Parametric Bike light housing for the cheap chinese models which are found here: https://www.amazon.de/DKINs-Fahrradlicht-Wiederaufladbare-Fahrradleuchte-Wasserdicht/dp/B07WZPTDWZ/ref=cts_sp_2_vtp The mounting hook broke and I desiged the new housing...

This is ESP8266 NodeMCU controlled 8 led NeoPixel ring rear bike light case. Part List: 1 x ESP8266 NodeMCU 1 x 750 mAh Li-po battery 1 x male-female battery connector 4 x M3 male-female Spacer Screw Nut 4 x M3 nut 4 x M3 screw for any...

Mount to replace a broken part of a bike light. ...Print Settings Printer: Cubicon Single Rafts: No ...

... lamp with diameter 41.5mm. The pedestrians will no longer be blinded. 0.8mm walls. One hole for M3 screw to fix the cap. Dont use white plastic. The best is dark, and paint the inner surface in white for better reflection of the light.

I have a bike light that used to have a belt clip. The belt clip snapped off, so it had been sitting in my junk drawer. Now it's useful again! Instructions Printed raftless on my Replicator at 10%...

The cheap LED flashlights at Harbor Freight fit in this also.   *** UPDATE **** I've added three new bike mount parts (UC-Bike-Mount-V2, UC-Bike-Mount-V2-Top, UC-Bike-Mount-V2-Bottom) for increased strength. You won't have to try and snap the mount...

I designed this light mount to fit on the fork blades of my old Schwinn bike. Its fork blades are about 1/4 in thin and made of solid forged steel. If you wanted to use this on tubular fork blades, I included the step file so you can redesign the...

Stunning Handlebar Light holder. ...You will need this...

Couldn't find a mounting clip to fit this type of bike light which slides on so here it is. Light has a full metal construction including the clip, rest of the mounting system is plastic with nuts & bolts. One I have is a Ocoopa KX3, could be sold...

This is a small light mount that goes onto the front of a bike basket. It allows you to attache any light with a rubber strap onto the front. Designed to use 2 m4 bolts and nuts. I used a Zortrax M200 3D printer and used ABS to print. I printed it on...

... können/ sollten weiter verwendet werden. An adapter to attach the original mount of the IXON Core battery front light to a normal front light bracket on the bike fork. The original screws can/should still be used. ... Translated with Deepl.com

Couldn't find a mounting clip to fit this type of bike light which slides on so here it is. Light has a full metal construction including the clip, rest of the mounting system is plastic with nuts & bolts. One I have is a Ocoopa KX3, could be sold...

3D printing files (*.STL) for the Bike Tail Light. ...To complete the light you will require also the following parts: -TP4056 1A Lithium Battery Charging Board (2,6 x 1,7 cm) -Lithium Battery (18650) -Toggle Switch MTS-102 or similar (Mounting...

A bike tail light idea I had. It fits a 10cm x 10cm EL Panel. It also can attach to a standard bike reflector with nut and bolt or screws of correct sizing ( 10mm ) The size is actually a bit small for the 10 x 10 panel so you can choose to let it...

Inspired by the studio Ghibli character from My Neighbor Totoro, this rear bike light can be slid onto the seat post of a bike (you many need to rescale to fit your specific model; the hole has a set diameter of 27.5 mm right now).  The electronics...

... kept falling out after a few rides. I used a 5V LED strip and used XT-30 plugs for easy taking of, and then connected it to the existing light cable of my E-Bike. ... You can probably also modify it to use some kind of battery for normal bikes.