bike support 3d models
585564 3d models found related to bike support.grabcad
My project for this challenge has as functionality loaded objects for a bike ride, including water bottle, cell phone and everyday accessories, for example, sunglasses and headphones.Obeservation: I used two screws and two butterfly hanuts to fix the...
thingiverse
Led bike support in case you need a spare one or you've lost the one with the purchased led at Decathlon store
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
GoPro bike support for JJRC X9 controller (other models are also valid) Soporte para bici-moto del mando del dron JJRC X9 para unir con el soporte de GoPro (también válido para otros modelos)
grabcad
Bike support for Bryton GPS equipment (specific used for Rider 420E). It does not clicks and secures but has a safe support and solid assembly. No problems. Files for changing or just 3d printing. ...I used epoxy glue to connect both parts.
thingiverse
This is a samsung J5 support for bicycle. ...Mobile fits perfect after some improvements in the first design(I have printed a prototype that was wrong calculated). For the installation you will need 2 bridles to fix the device to the bike stem.
thingiverse
So I create this support for my bike, which always have the phone in front of me and without removing it from its protection. For Plexiglas, go to the radius picture of a DIY store and it costs € 2 cut with a knife. I hope this can help you. I let...
thingiverse
I broke the support for my back light so i dessigned a new one to replace it.
thingiverse
It adapts perfectly to all NCM E-bikes, also known as MAGNUM E-bikes in North America, but it can be fitted to all bikes equipped with the same rear metal plate (see the technical diagram in the figure). ... A more compact and stable adapter is now...
thingiverse
HI, I just created a replacement support for my bicycle torch SIGMA buster 100. I highly recommend printing it in ABS. ... To build this project you need : - x1 : M3 21mm - x1 : M3 15mm - x2 : M3 Nuts Good...
thingiverse
Customizable support of a pump for a bike. ...Support base is curved according to a curvature of a tube in radial (small radius) and axial (big radius) directions.
thingiverse
Bike light support. ... Designed with Solidwork and printed with JG AURORA A3S 3D Printer
thingiverse
ENG : Bike Pump support Diameter of pump ~ 25.5mm FR : Clip pour pompe decathlon à mettre sur vélo (Pompe vélo à main B.Twin 920 télescopique avec manomètre) Files : STL...
pinshape
This bike shoulder support can help you carry it easily such as go upstairs to your home, etc. I've used red foam to make it more confortable. Printed with PLA but you can use the material you want. ...You can find the printer settings attached here.
sketchfab
Maillot Marathona Maillot ligero y aerodinámico Tejido StradaPro 3D en la espalda proporciona sujeción a los bolsillos y una protección solar UPF 16 El tejido Flusso 3D 75g/m2 en la parte delantera y en los hombros mantiene el maillot ligero y seco...
thingiverse
It has been designed to fit in the bike stem, so you have to unscrew the cap, put the support (acts as a 1cm spacer) and screw again the stem. Sturdy, low profile, to avoid getting stabbed with the cam in the chest. You need a nut to fit in the...
thingiverse
If you have the Ibera bike rack like I do https://www.amazon.com/gp/product/B00DWKUAZK than you are in luck, you can use the hardware that you get with the varia and you should be all set.
thingiverse
support go pro diamètre 32 mm pour guidon de vélo Fabrication en rapide 0.2mm et remplissage 33% Temps de fabrication avec maintien 1heure 10minutes
sketchfab
Culotte Volo Badana KISS Air confortable durante todo el día Tejido Affinity Lycra® en el interior de las piernas para mayor elasticidad y soporte muscular. ...Tejido Affinity BLC en las piernas para mejorar la aerodinámica Terminación piernas en tejido...
thingiverse
To print this you will have to adapt the radius of the handle bar by default it is 35.2mm. The angle is 15deg but can also be adapted. I used the black fix that came with the gps. ... EDIT: The version 2 has a better angle for visibility, it also...
grabcad
Designed for the Sunstar challenge, the idea to finish off the model with a slim direct drive motor.
thingiverse
For bike stands that support bikes via the rear skewers. A placement holder to prop your bike frame on while you service & wash your rear wheelset. ...