bird tree topper 3d models

My wife wanted a start that fit in with the theme of the stars you see below:Designed to fit this light:https://www.amazon.com/Accessory-Cord-One-Light-Bulb/dp/B07W726LD5?th=1The base should print nicely without support but the insert will need them...

<p>Print the 20-sided core, 19 tetrahedrons and one foot. Spray in Gold. ...Use superglue to assemble.</p><p>5% infill or less recommended except for the foot (15%) there.</p>

I really liked this basic design but wanted to be able to print it in two sections, needed to hollow out the base, and insert alignment holes for the parts. I used Blender to make these modifications. The holes are designed to accept a small piece of...

The star is splitted in 2 parts that need to be glued/fused together.The base can be printed without support.

I created my own basic star model with clean flat faces since I couldn't find one already available. To achieve optimal results, I suggest printing the design upright and omitting bottom layers entirely - this is essential for creating a hole in the...

I give all credit to gshorts for the original design. I utilized netfabb to reorient the objects for simpler printing. If I were to print another one of these in the future without a looming Christmas deadline, I might opt for a finer print...

<h4>Height</h4> Measuring 220 millimeters tall. <h4>Bottom Hole Diameter</h4> Compressing to a diameter of just 18 millimeters at the bottom. ... <h4>Software Development</h4> Carefully crafted in Cinema 4D using Loft Nurbs technology.

Adjust your slicer settings to match your printer's bed dimensions, which are 330 by 330 millimeters square.

Enjoy the magic of Christmascheck my patreon page and if you like it maybe you want to support me and my work. ...Thank youhttps://www.patreon.com/DonCipriano3D

Create a festive decoration using RGB self-changing LEDs by cutting parts from a 5mm acrylic sheet using a dxf file and a laser cutter. Assemble the star with five M3x20mm screws and mount it with two M3x16mm screws. Sand the top layer with 80 grit...

Merry Xmas Everybody

Festive Finishing Touch - Elegant Apex Adorns Christmas Evergreen Emblem

<p>I couldn't find a basic star with clean flat faces so I modeled one for myself. I recommend printing it upright with zero bottom layers (to make the hole) and supports for the bottom edges of the spokes on the star. I attached an image of the...

I designed this to allow for putting a medium size bulb (mine is 27mm at the widest) inside to light up the star. You could also add the bottom point, just be aware that the bottom hole is slightly larger than all the others. I originally tried...

A Volkswagen inspired Christmas star.

This unit measures 1.9 times its original size, boasting a prominent star at the center. Its sturdy peg measures 15mm in length, 5.25mm in width, and 6mm in height. ...The entire structure reaches an impressive 106mm in height.

Here is a custom version of http://www.thingiverse.com/thing:1159436. Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=1159436. ... **Instructions** Using the following options: Target Diameter Set to 100 mm Sharpness...

i hope you like it! ...

Made from 2 pieces to be mounted together with an M3 Screw. Spray paint glitter ... it's up to you. Hope you enjoy this design. ... My other thoughts ....need to make it lighter in future.

Enjoy! ...Will need to enable supports for the the face.

It prints well on a Prusa 220x200 when you rotate it on the bed 45 degrees. ... The OpenSCAD design was build from scratch by me.

I printed this on a Prusa Mk3s. Layer height .2 You may or may not need supports depending on your machine. Print twice, and them glue or tape seams. I used a 16 LED neopixel ring to light from the inside. Lights are controlled via an adafruit...

In your slicer set up the initial bottom layer to 0, infill 0% and the wall line count to 2. Recommended to use brim with at least 10 line count for a better adhesion. ... I used white PLA and I put the christmas lights under it.

Merry Xmas Everybody

Made from 2 pieces to be mounted together with an M3 Screw. Spray paint glitter ... it's up to you. Hope you enjoy this design. ...My other thoughts ....need to make it lighter in future.

A friend asked me to remix this and add an extra cone, so I did just that. ...To get the desired result, I printed it at double scale, and I'll post it online once it's complete.

I replaced the hooty face with this one https://www.thingiverse.com/thing:4744918 and scaled it to fit nicely then sliced it into more easily printable parts, optimised to only need supports on the house section

Print 2x and glued together