blade nano qx 3d models
42701 3d models found related to blade nano qx.thingiverse
I recently bought a Blade Nano QX quadcopter in order to practice my indoor flying and decided to replace the cover that came with it. This is a simple spiral design that I created in Fusion 360. There's a video of this drone in action here:...
thingiverse
This is a simple 10pc. ...battery holder for the Blade Nano QX.
thingiverse
This is a remix, I really liked the blade nano case that dgwinner made, but because I made the antenna protector and installed it, my nano would not fit in this case. It was too tall. So I basically made it deeper. A lot of people had problems...
thingiverse
Once this is done I want to design a Mavic Pro inspired Nano QX folding frame. Print Settings Printer: Monoprice Select Mini Rafts: ...
thingiverse
I usually fly the small Nano QX 3D Quadcopter outside at night and have a pocket full of batteries (probably not the best idea). I drew this holder for 6 batteries, made it fairly deep with the pockets large enough to accept either end of the...
cults3d
Frame anti obsolescence for Blade Nano QX 3D the frame is made for the more powerful engine than 8 mm). ... Video: https://youtu.be/B-eR4ecCVa8
thingiverse
Frame anti obsolescence for Blade Nano QX 3D the frame is made for the more powerful engine than 8 mm). ...Simply solder the motor son on the feet pad arms The flight controller esc holds integrate with 8 mm motor in normal flight mode for 3 minutes...
thingiverse
My standalone Spektrum VA1100 uses left aligned saver, the one that came with Blade Nano QX FPV uses centered saver. It should sit tight on the pins inside, if it doesn't fit, file the bottom corners a bit. ...
thingiverse
Remix of http://www.thingiverse.com/thing:809885 to fit the Micro Motor Warehouse 6mm motors. It is set to 6mm hole, but the motors are 6.2mm in diameter, so you need to bore out a little with an xacto knife to fit properly. ...Print Settings Printer...
thingiverse
This is a case that protects your Nano QX quad copter during transport. The case includes 4 pockets for spare batteries and comes with an optional lid component. Update: V1.1 adds a holder for the charger and 2 additional pockets for batteries and...
thingiverse
V1 of my small quad frame for NanoQX components from Blade. Still working on it but it flies very good so far! ... V2 ONLINE NOW!!http://www.thingiverse.com/thing:318081 Print with no support and 0,2mm Layer - Infill 20%
thingiverse
simple clip-on-mount to to put 2x 5mm-LED's to the nano QX FPV camera mount. Just print, take 2 LED's and the corresponding resistors, solder everything together and plug it into the LED holders... Simple to clip on/off as needed. ... The power...
cgtrader
... this is speed deamon you have to fly. Also comes with starting block to help you fly in self stabilizing mod inside of house or office. If you need option with straight motors just let me know. this frame work with all oryginal blade nqx parts
thingiverse
This is e repaired version of KiLLiN-TiMe's version (https://www.thingiverse.com/thing:1266503). ...The lid didn't print correctly, so I repaired this and now it prints fine.
thingiverse
This is based on http://www.thingiverse.com/thing:617052 but is fixed. The original version of this model was not watertight and therefore did not print correctly. This prints properly (the lid is a bit tight though, might rework that in the near...
cults3d
This is based on http://www.thingiverse.com/thing:617052 but is fixed. The original version of this model was not watertight and therefore did not print correctly. This prints properly (the lid is a bit tight though, might rework that in the near...
thingiverse
New Version of the small frame. ... better wire support for motors more stable motor mount ( 2 Layers ) reduced weight by removing unless parts Instructions Printed with 2 perimeters, 2 layers...
cults3d
Kamera-Halterung fuer Boscam CM205 auf Blade Nano QX. ... Camera mount for CM205 Boscam on blade Nano QX.
thingiverse
Kamera-Halterung fuer Boscam CM205 auf Blade Nano QX. ... Camera mount for CM205 Boscam on blade Nano QX.
youmagine
Frame anti obsolescence for Blade Nano QX 3D the frame is made for the more powerful engine than 8 mm). ...Simply solder the motor son on the feet pad arms The flight controller esc holds integrate with 8 mm motor in normal flight mode for 3 minutes...
thingiverse
This is a Race Quadcopter inspired frame for the Blade Nano QX. It is about 2g heavier than the original one when printed in PLA. The quad is in my opinion a little more agile than with the original frame. The stock and most of the aftermarket...
thingiverse
I tried to make a frame for the Blade Nano QX that is lighter as the original one. So that it may be faster and more agile. Place the flight controller with a double sided tape in the center of the frame. The tape should be around 1.7mm thick. ...
thingiverse
Blade Nano QX battery and usb charger stand. Holds the USB charger and 6 batteries. It's designed with 2mm thick walls throughout to give it some weight so you can remove a battery one handed. If things are fitting a bit too snug, try scaling...
thingiverse
I just printed a small Case, to carry my Nano QX fpv in my Backpack. I really like how the shape turned out ! The Top is hold by friction fit tabs, holds it together very strong. ... On the Picture you see the prototype design, which was 3 piece (two...
thingiverse
LENS PROTECT NANO QX 2 Print Settings Printer Brand: RepRap Printer: Prusa i3 Rafts: No Supports: No Infill: 100
thingiverse
This is a Nano QX frame I designed in FreeCAD. I'm not sure how it even performs, weighs, etc. ...because I don't have a 3D printer, but here it is.
thingiverse
Utilisables avec la carte du nano qx de blade et des moteurs coreless de 6 ou 7 mm. (type chaoli cl-... que vous pouvez trouver par exemple chez micro-motor-warehouse.com) Il vous faut également des batteries 1s type "baton". (E Flite, Parkzone...