blf lt1 3d models
101 3d models found related to blf lt1.thingiverse
Reflector for the Sofirn BLF LT1 lantern. ...I used duct tape for the reflective surface.
thingiverse
BLF LT1 lantern as a reference for you mods and accessories. ...Outside dimensions are as accurate as I could measure them.
thingiverse
This is the shade I designed for the BLF LT1 Lantern. I print it in PETG at 0.16mm on my Ender 3 v2 I print with a RAFT for best success. ...
thingiverse
A simple base for the BLF/Sofirn LT1 lantern. ...The cutout in the bottom is for a ring of rubber or foam.
thingiverse
A simple base for the BLF LT1 LED Lantern - a community-produced LED lantern of epic proportions. Come check it out here! http://budgetlightforum.com/node/44923 This base is held on by friction, I printed this on my MP Select Mini V2 and it fits...
prusaprinters
A simple base for the BLF/Sofirn LT1 lantern. There are two versions: v2: Wider, thicker version. The cutout in the bottom is for a ring of rubber or foam.</p> <p>v3: Slightly smaller and more minimal version. ...It is as wide as the head of the LT1 so...
thingiverse
The BLF (Sofirn) LT1 is a very nice lantern, but sometimes the glare gets annoying. Wouldn't it be great to block the light in one direction? Now this is possible with this simple design that can be clipped to the LT1. You can use it either as is...
thingiverse
A simple lamp shade for the BLF/Sofirn LT1 lantern. There are two versions available: v1: My original idea, but my printer struggled with the 60° overhang at 0.2 mm layer height. v2: Slightly different design with a maximum overhang of 50°...
prusaprinters
Reflector & base for BLF LT1 Mini lantern. Reflector & base both require a magnet. The reflector uses an 8x3mm magnet. The base uses <a href="https://www.kjmagnetics.com/proddetail.asp?prod=D82-N52">this magnet</a>. The reflective surface is...
prusaprinters
SOFIRN BLF LT1 Lantern StandI modeled this lantern stand in Fusion 360 for the Sofirn BLF LT1 (see below). The multi color effect is just two color changes at the right heights. ...It's about 3.6 inches wide, .5 tall.</p><p> </p>
thingiverse
A small shade for the Sofirn BLF LT1 Lantern. Gently directs the light downwards and reduces glare. Printed in 2 hourse with no supports at 0.1mm layer height. ...The low layer height improves the overhang.
prusaprinters
Fits snug and opens up the possibility of hanging inverted with the head/diffuser off for even overhead lighting using some paracord and some S biners to attach to the holes.I printed this in PETG, but PLA should work.much improved Multi-Function...
thingiverse
I use my BLF LT1 for a lot of things, many of which do not allow the use of this shade. I wanted a shade that was easier to install and remove quickly. Literally just added a 1mm gap in the shade, left everything else original. ...This way I could pry...
prusaprinters
I wanted magnets built into the tailcap of my BLF LT1 so I can stick it to surfaces, and I didn't want to have to carry around one of those tripod-thread magnets. This adapter holds six of <a...
thingiverse
This is a shade and base for the Sofirn BLF LT1 lantern. The shade is meant to help reflect light downwards, so print it in a light color or paint it with a reflective color. The shade is a very tight fit with a 35.65 inner diameter. FWIW, a...
thingiverse
Loving Cymond's remix of the BLF LT1 reflector which added a "retained bolt" feature, amongst other things, to Adair21's original design. Didn't have any 1/4-20 nuts handy that fit into the recess he designed, so I made this handy little retainer...
thingiverse
Brief On a Venn diagram, the intersection of owners of both an IKEA Jerker desk, and a Sofirn BLF LT1 lantern probably amounts only to a small set, but if you're a member of that set, this may be for you. The LT1 is a good lantern, but the ratio...
cults3d
I UPDATED THE DESIGN IN THINGIVERSE but Cults is refusing to sync the changes. See The pics here: www.thingiverse.com/thing:5322852 The original version by Adair21 is great, but large. I altered it to work with my own top shade design. This meant...
thingiverse
I'll post pictures soon, but for now, here are the STL files. The original version by Adair21 is great, but large. I altered it to work with my own top shade design. This meant scaling it down, and making it shorter to fit under the shade. I...
cults3d
A model of a light tank, created by me according to the rules of BT. Scale for 6mm. Divided for convenient and easy printing (includes a connoisseur undercarriage). There are 2 versions available. Ballistic and energetic. Floats. The turret and case...
thingiverse
Diffusor for the BLF Q8 flashlight. Printed with bq transparent filament, 0.1mm layer height & 30% infill for better diffusion. v1 is ~60mm high vs. ...~110mm for v2
thingiverse
Hello, here is a Cover to protect the Lensglas of the Monster Flashlight BLF GT von Lumitop. The Logo is inside the Cover.. ... Now in Version V2 with mirrowed Logo that shines to the front
prusaprinters
Diffusor for the BLF Q8 flashlight. Printed with bq transparent filament, 0.1mm layer height & 30% infill for better diffusion. v1 is ~60mm high vs. ...~110mm for v2</p>
thingiverse
Simple drop protection bumper to go on the front of a BLF A6 torch. Print in TPU. It might block the outer edge of the light a little, but nothing noticeable. ...