bltouch ender 3 3d models

My new (and first) Ender 3 MAX came with BLtouch mounting holes to the right of the hotend so I re-purposed the BLtouch from my dead Cocoon Create Touch. I couldn't find a suitable existing mount so quickly designed my own in Fusion360. ... ...

... the mount in place of the larger idler wheel mount screw. I believe they are m2.5x0.45 screws. I used the wiring guide and configuration/firmware found here: https://smith3d.com/ender-3-v2-bltouch-firmware-installation-guide-by-smith3d-com/

... it holds up, but so far so good... There are apparently 2 versions of the Ender 3 V2 - One of the versions does not have the mounting holes that this attaches to, so... ...:/ The nozzle to probe offset I'm using with this is X-40, Y-7

Bltouch support. Just fixed by the 2 small holes on the plate. No disassembly to do. ... I redesigned it because the one I had downloaded put the sensor too low compared to the nozzle.I moved it up 3mm.

Remixed from the original that had the dial gauge mount. ...Uses original hardware

I had to find (ender3Maxconfig files) and compile my own firmware using marlin->visual studio code->Platformio extension https://www.youtube.com/watch?v=-76t_fOhb2M Creality ENDER 3 MAX BLTOUCH - How To Install in 3 Easy Steps...

... Printed on Ender 3 Pro PLA 210c, 0.2 layer height, 0.3 layer width, 100% infill. Used brim and support with support roof and bottom, touching buildplate only, and model standing upright(cable mount upwards). ...I think the stl might be upside down.

... Printed on Ender 3 Pro PLA at 210c, layer height of 0.2mm, layer width of 0.3mm, and 100% infill. ... Brim and support were used with support roof and bottom, touching the buildplate only, and the model was standing upright (cable mount upwards).

... with the left M5 screw. ...Used with 3D-Touch Sensor. High above the bed is 8.3mm Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0,2 Infill: 20 Filament: Das Filament PETG black Category: 3D Printer Parts

The STL I got from PrinterMods support for the BLTouch mount Ender-3 MDD 1.2

The STL I got from PrinterMods support for the BLTouch mount Ender-3 MDD 1.2 Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Doesn't Matter Resolution: 0.2 Infill: 25% Filament: Polymaker Polyflex PLA Black Category:...

The STL I got from PrinterMods support for the BLTouch mount Ender-3 MDD 1.2 Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Doesn't Matter Resolution: 0.2 Infill: 25% Filament: Polymaker Polyflex PLA Black ...

Reinforced BLTouch mount for Ender 3 Max with captive M3 nuts. M3x 8mm screws and optional washers. Suggest printing in ABS or PETG incase you plan to print with higher temp filaments in an enclosure. ...

... is a remix of https://www.thingiverse.com/thing:3003725. Duct blower is a remix of Prusa hotend. Print all parts, use 2x M3 brass insert for blower fix and 2x M3x7mm screws For the rest recycle all Ender 3 screws of stock Hotend and related parts.

Useful links regarding the BLTouch: BLTouch Documentation: https://www.antclabs.com/bltouch-v3 Marlin Firmware (now configurable for Ender 3 V2): https://marlinfw.org/ Already configured firmware: https://marlin.crc.id.au/ Creality Firmware:...

This is remix to be compatible with Ender 3 V2 extruder plate which is has different screw hole. I also add BLTouch mount to straight blower holder. ... BLtouch offset 34.5, 9

updated orginal design for Ender 3v2 and removed interference with roller screw and added second screw hole. ... similar design for Ender 3 after upgrading to direct extrusion.

X-Offset -43 Y-Offset -10 Mounted only with the left M5 screw. Used with 3D-Touch Sensor. ...High above the bed is 8.3mm

I crafted a custom BLTouch Mount for my Ender 3 printer, specifically designed to accommodate a shorter Chinese hotend that falls short of the original. My nozzle would never make contact with the bed, even when the BLTouch was retracted and elevated...

Please give it a ❤️ if you like it 🥰I designed this BLTouch Mount for my Ender 3 because my chinese hotend is shorter than the original one. ...The nozzle was never touching the bed even with the BLTouch retracted and upped at the maximum using the...

I didn't care for the way it flexed while everything else on the Ender 3 is solid. The problem is it only mounts solid on the fan mounting tabs. The rest of it is unsupported. My solution was to cut away the back side in Fusion 360 where it meets...

A Simple Mounting Bracket for the BLTouch Sensor

A simple BLTouch Mount for the Bullseye Base Current status: I have only mounted the BLTouch but not tested it yet. My design comes in two versions: The normal version is the one I use myself, but has the disadvantage that the screw on the left...

Be sure to screw the left screw first, and then secure the Hotend (2.5cm screw needed). The right side doesn’t stay in place properly, so don’t worry about it. You can easily use the stack V6 Fan, and soon I will update a version that support the...

This is a modification of the modification by eric_csuf of the original by registeredthing: Since I converted my Ender 3 Pro to Direct Drive (Ender 3/Ender 3 Pro Direct Drive Extruder UPGRADE KIT from skynet3dmods), I had to make slight adjustments...

... PETG or upgrade to superior ABS for exceptional results. ... The fan duct was carefully printed exactly as depicted in the thumbnail image screenshots. To ensure precise calibration of my BLTouch sensor, I set the offset values to X: -56.8 and Y: 0.

I've checked out mday10's thing on Thingiverse, which has all the information needed, including his BLTouch mount and a pressure clip that he designed. I also took a look at his creation, which is a bit more rough around the edges than the original,...

This is a remix of Voron afterburner mount for Ender 3 (bmg direct drive) https://www.thingiverse.com/thing:4614384 I will tag it as a remix once Thingiverse is working again. This is for the newest version of the Afterburner, not the beta 1 version....

... to use a V6 silicone sock and implement PID tuning. A Noctua NF-A4x10 FLX fan (DC-12V) and a radial fan measuring 50x50x15mm (DC-24V) are employed for optimal airflow. Key settings include: BLTouch Offset, X=57.0 | Y=2.2. ...Have fun printing!

Update (3/24/21): Added clearance for wheel bolt Update (3/18/21): Fixed slot clearance on wire guide As title says, I took a few models and glued em together using tinkercad. This uses the stock fans. ...this will NOT work if you have an all metal...