blue snowball adapter 3d models
159839 3d models found related to blue snowball adapter.thingiverse
A small bracket for adapting the blue snowball onto the end of a swing arm lamp. Similar to This one on amazon. The Peg is slightly oversized, to allow the microphone to cut its own threads. A small bump is included on one side to help with rotation....
thingiverse
I made this simple adapter to be able to attacth my Blue Snowball to my smartphone tripod.
thingiverse
... one I found here was wayy too big. ...This one is made to perfectly fit the silver "stem" that screws into the blue snowball. ----------------------------------- Very easy print, supports only needed if the look is a concern. ...support angle 60
thingiverse
With this mount, you can easily adapt your Blue Snowball ICE microphone to work with a shock mount on a boom arm or wherever you mount it. Simply disassemble the stock stand that comes with the microphone, take the legs out of the stand itself,...
thingiverse
A cheap and easy solution to convert your snowball into a handheld mic. ... Video on the topic: https://youtu.be/DdlsjZNpgUU
thingiverse
This is an adaptor for using a Yeti shockmount with the snowball. It needs an M4 screw to hold the threads to the ring-mount. I also used M4 torx screws for the ring-mount as I lost the original screws. This thing was made with Tinkercad. ...Edit...
thingiverse
This is an adapter for Blue Snowball as simple as it gets. ... It was made to fit Røde PSA-1 microphone arm, but 3/8 is a fairly common threadsize for many arms.
thingiverse
a shorter stand for the blue snowball microphone, or softballs i'm not your mother.
thingiverse
Simple stand to replace my blue snowball mount (non-adjustable) after I accidentally dropped and broke the original one
thingiverse
Remix of my original blue snowball mount, 2 Sizes small and large, Addeds some adjusta ability on hight. 6 x M4x8 required for hight adjustablity. ...
thingiverse
A clamp and screw created to hold your blue snowball microphone. ...Prints in three different pieces designed to require no glue, all pieces should fit together snugly.
myminifactory
This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. V4 sits lower. ... Fusion 360 archive...
thingiverse
This is a pop filter I designed to work with a Blue Snowball microphone. I super glued part 1 into part 2. ...then stretched a knee high stocking over the hoop trimmed it up a bit and used a rubber band to cinch it up at the bottom.
thingiverse
A tall, simple, stand for microphones that use 5/8"-27 UNS threads, like the Blue Snowball. I thought the stock stand was too low, and I wanted a stand where the mic was close in front of my mouth, not below me. I used dynamic layer height in...
thingiverse
This is a pop-filter for the "Blue Snowball" microphone. All you need to do is to insert a piece of, for example, pantyhose, between the two parts and click them together. The filter itself attaches to the shaft of the microphone as a clip. ...
thingiverse
Key differences from other mounts was the use of through-hole bolt-in mounts, a cord-clip, and precise thread printing for the 5/8-27 Microphone mount on the Blue Snowball and Blue Snowball iCE's OEM Stand. What you Need For this Mount...
thingiverse
Mic/camera stand for over your monitor/tv, adjust it for your model. ... This exact is for the Blue snowball mic. ... Use PLA with infill at 10-20%
thingiverse
wanted a small tripod to hold up my camera, had this old one from my blue snowball mic. ... Currently using a #8 bolt holding it together.
thingiverse
A pop filter for your Blue Snowball mic. The shield itself is a used dryer sheet. ... Since this is parametric, you could theoretically use this on other mic stands with some experimentation.
thingiverse
**Required Materials** - 1 Adjustable Stand (included with your Blue Snowball iCE) - 4 Hair Ties **Notes** You'll need to remove the legs from the adjustable stand. ... **Changelog** - Added an elongated version of the outer mount to accommodate...
thingiverse
... stand does require these rubber bumpers. 10mm x 4mm https://amzn.to/2HCik22 You may also be able to find them at your local hardware store. Rather buy it? Get it here: https://www.etsy.com/listing/897026717/blue-snowball-low-profile-stand
thingiverse
Utilized another users threading attachment for the blue snowball and modeled some couplers to be able to attach to the end of the arm. Extremely solid, however, the mic couplers have not had enough testing so use at your own caution. Bolts need to...
thingiverse
Bracket mount for a Blue Snowball ICE, attaches to the back of a monitor suits 100mm distance between two bottom screws (longer screws may be required). does bounce around when moving the monitor, but stays still when not touched. ...great to keep it...
thingiverse
Hey guy today I bring you a simple and yet effective adapter for the SnowBall mic . ...I printed at 50% infill Subscribe to MrJefferson105 Print Settings Printer Brand: Prusa ...
thingiverse
I created a fairly simple shock absorber for my Blue Snowball. You will need: 2 x inner ring pieces 2 x outer ring pieces superglue 8+ hair bobbles Thread the bobbles through each loop and hook onto neighbouring pins. The microphone should...