blue snowball mic arm 3d models
125625 3d models found related to blue snowball mic arm.thingiverse
This is a simple gadget to attach a Blue Snowball (or other) microphone to a standard "lamp arm" and it also includes a pop filter. The bird is not included :-) Arm_long.stl and ring_center.stl have to be glued together. I've included the part...
myminifactory
This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. V4 sits lower. ... Fusion 360 archive...
thingiverse
Utilized another users threading attachment for the blue snowball and modeled some couplers to be able to attach to the end of the arm. Extremely solid, however, the mic couplers have not had enough testing so use at your own caution. Bolts need to...
thingiverse
... part, as it contains M15.5x1.0 thread, which is pretty fine and could turn out not well enough). No supports required. This model is set remixed as the thread to the mic stand is taken from the 'Blue Snowball Mic Armature Mount' by Janbro. ...
cults3d
The Blue Snowball leg joint on the stand is not that strong. Designed in Fusion 360, simply print and screw in the new one. ... 30-40% infill with .2 layer height gives plenty of strength using PLA.
thingiverse
Needed a small form factor pop filter for my snowball mic and i didn't feel like spending 20$ on a few cents worth of plastic, print 2 of the mesh holders, glue a piece of thin fabric/mesh between them before gluing them into the model itself. ... 2...
grabcad
This should fit any variation of the blue snowball mic, but if it doesn't just hit the hands with a gentle heat gun and use the mic to deform them to fit.
thingiverse
This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. ... V4 sits a bit lower Fusion...
cults3d
This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. ... V4 sits a bit lower Fusion 360...
thingiverse
A small bracket for adapting the blue snowball onto the end of a swing arm lamp. Similar to This one on amazon. The Peg is slightly oversized, to allow the microphone to cut its own threads. A small bump is included on one side to help with rotation....
thingiverse
... out the temporary supports on the desk attachment. When attaching the mic, use the little rubber washers between the mic itself and the printed part. ...The dimensions match the holder that the mic comes with so it fits together the same exact way.
thingiverse
you might also have to tighten up the rest of the screws on the arm to support the extra weight of the mic. For the mic i used the original stand and took off the folding legs. just unscrew the screw on the very bottom of stand and take out the legs...
thingiverse
Made this to keep my Blue Snowball from rolling off the desk and wrecking house. Enjoy! ...Threads made possible by: https://www.thingiverse.com/thing:193647 Print Settings Printer Brand: Printrbot ...
thingiverse
Microphone stand for Yeti blue snowball mic. ...I wanted to make it shorter, but the USB cable angles down, so this gives the cable enough clearance, while still lowering the mic under my monitor.
thingiverse
Hey guy today I bring you a simple and yet effective adapter for the SnowBall mic . ...I printed at 50% infill Subscribe to MrJefferson105 Print Settings Printer Brand: Prusa ...
thingiverse
This is a short desk stand for the Blue Snowball microphone. I designed this to be able to fit the mic below my monitors. The existing designs I found didn't have any space between the base plate and the mic meaning it wasn't possible to tilt the...
thingiverse
a shorter stand for the blue snowball microphone, or softballs i'm not your mother.
thingiverse
A tall, simple, stand for microphones that use 5/8"-27 UNS threads, like the Blue Snowball. I thought the stock stand was too low, and I wanted a stand where the mic was close in front of my mouth, not below me. I used dynamic layer height in...
thingiverse
Simple stand to replace my blue snowball mount (non-adjustable) after I accidentally dropped and broke the original one
thingiverse
Remix of my original blue snowball mount, 2 Sizes small and large, Addeds some adjusta ability on hight. 6 x M4x8 required for hight adjustablity. ...
thingiverse
A clamp and screw created to hold your blue snowball microphone. ...Prints in three different pieces designed to require no glue, all pieces should fit together snugly.
thingiverse
What you Need For this Mount ----------------------------------------- * Blue Snowball or Snowball iCE Microphone * Blue Snowball or Snowball iCE Microphone stand * Two (2) Prints of the Outer Rings * Two (2) Prints of the Inner Rings * One (1)...
thingiverse
This is a pop filter I designed to work with a Blue Snowball microphone. I super glued part 1 into part 2. ...then stretched a knee high stocking over the hoop trimmed it up a bit and used a rubber band to cinch it up at the bottom.
thingiverse
This is a pop-filter for the "Blue Snowball" microphone. All you need to do is to insert a piece of, for example, pantyhose, between the two parts and click them together. The filter itself attaches to the shaft of the microphone as a clip. ...
thingiverse
Keeps the 'pops' away for your mic. I used a nylon sock for the air flow in between the printed parts. Instructions The clamp is mounted with a screw. For the air flow in between the filter I used a...
thingiverse
Print Settings Printer: MP Select Mini Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.0875 and 0.175 Infill: 20% AND 100% Notes: -Scew and Nut should be printer as follow: Resolution: 0.0875 Infill: 100% Speed: 30mm/s or slower than...