blue yeti stand mount 3d models
522673 3d models found related to blue yeti stand mount.thingiverse
These are a couple of mounting stands for a Blue Yeti USB microphone. There's a hole at the base to accept and hold the head of a 1/4-20 bolt for mounting to almost anything. A 1/4-20 wingnut or brass knurled nut makes it easy to tighten by hand. ... ...
thingiverse
The metal stand that comes with the Blue Yeti mic is too heavy for a 2-segment wooden extension arm I built, so I created this mount/yoke in FreeCad to make a lighter mount that I could bolt to just about anything. There are 2 variants: - The short...
thingiverse
I lost the stock stand for my Blue Yeti USB microphone, so I designed this stand with a slot for the oval extrusion on the bottom of the microphone to fit into. There is a slot for the USB cable to fit into, but I did not design a similar slot for...
thingiverse
A quick mount for the Blue Yeti microphone so it can attach to a VIVO monitor stand. Designed for a ~35mm diameter monitor stand. ... .step and .f3d files included.
prusaprinters
The stand in the photo is the 100mm version, but I also include a 75mm version that is a bit smaller. That should fit with the cord.</p><p>The knob use a normal M6 Hex screw bolt 20mm. ...Normal 6 sided head (bolt head).</p>
thingiverse
Designed this Blue Yeti mount because I was tired of my swivel arm desk stand not being able to position the microphone the way you're supposed to speak into it. I used the washers and thumbscrews that come with the metal table stand that ships with...
thingiverse
I designed this after realizing I could not buy arm mount for my blue yeti nano. This can be printed directly on the bed. I made the hole in the back fit my arm mount directly and was able to just thread it in. Ill probably add some indents to...
prusaprinters
Basic top cover with webcam mount for a Blue Yeti microphone complete with thumb handle for easier moving. ...Designed to be used with a boom arm and webcam with a tripod mounting thread.
prusaprinters
A quick mount for the Blue Yeti microphone so it can attach to a VIVO monitor stand. Designed for a ~35mm diameter monitor stand. .step and .f3d files included. Print instructionsCategory: Office Summary A quick mount for the Blue Yeti microphone so...
thingiverse
Shock mount for the blue yeti microphone. Screws into the microphone like the original stand and uses the same screws, so there's no need to go out and buy any. It has a manfrotto 323 compatible quick release plate built in (optionally), but if you...
thingiverse
All you need to make it is a scissor arm or any standard microphone mount ###YOU MUST PRINT WITH SUPPORTS OR THE OUTER RING WILL NOT PRINT RIGHT [Amazon...
thingiverse
This is a generic shock mount for the Blue Yeti Microphone intended to be used on some sort of boom arm. It uses hardware that you can get from your local hardware store (Bunnings in Australia). ...I had lost the screws that came with the microphone and...
thingiverse
... thing! ... Anyway, I wanted a mount for my microphone to keep it off the desk and there wasn't much out there :) Print Settings Printer Brand: FlashForge Printer: FlashForge Creator Pro Rafts: Doesn't Matter Supports: No Resolution: .2 Infill: 30%
thingiverse
Blue Yeti Mic Stand Spacer Lost the spacer to my Blue Yeti microphone and designed this replacement spacer.
cults3d
... stand that came with the microphone. There are marks on the bottom for the rubber feet, it is meant to use these: https://amzn.to/2PvTJQ1 Rather just buy one? Get it here: https://www.etsy.com/listing/974620483/blue-yeti-original-style-stand
cults3d
Looking for a more compact stand for your Blue Yeti? You've found it! This stand lowers the height of the microphone by 2.5" (63.5mm). ... I use these rubber feet to keep it from slipping around: https://amzn.to/3cMnkfF
thingiverse
Low profile mount for vertically mounting a Blue Yeti Microphone. ... OpenSCAD file included for customization
thingiverse
I wanted to use the Blue Yeti as a desk mic, but with my limited space it had to go between the monitors and keyboard without being in the way. I modeled this in 123D Design. ...Print Settings Printer: Cheap eBay Prusa I3 ...
thingiverse
Low profile stand intended to hold mic in a reclined position, since cardioid setting on mic picks up sound from in front of it (i.e. tilt mic back to talk into "Blue" logo). ... Uses same screws as original stand, Settings don't matter.
cults3d
The Original Stand was too high and Heavy. ...I modify the Mini USB connector slightly to fit at an angle. :-P I have printed the Stand in two pieces and glued them together.
thingiverse
The Original Stand was too high and Heavy. ...I modify the Mini USB connector slightly to fit at an angle. :-P I have printed the Stand in two pieces and glued them together.
prusaprinters
... USB connector slightly to fit at an angle. :-P I have printed the Stand in two pieces and glued them together. Print Settings Printer: Craftbot Plus Rafts: NoSupports: No Resolution: 0.4Infill: 20% Filament: Noname PLA Black Category: Office
thingiverse
This is a suspension mount for the Blue Yeti Nano. It allows it to be adapted into some anti vibration arm mounts. The screws and rubber grommets from the original stand fit perfectly into the main holder. The mic sits slightly high, but all buttons...
thingiverse
... Print so the layers are parallel to the long axis of this part. See Also Don't forget to check out my other Blue Yeti related parts: Printed Standoffs - used for spacing the shock mount inner rings Mounting Kit - side brackets and a 5/8" screw
thingiverse
The thumbscrews that are included with the Blue Yeti can be used to mount the clamps to the microphone body, as designed. You don't need to purchase hardware, just bungee cord. A mic adapter can be taken off of most mic holders (check model for...
thingiverse
A remix so you can mount a camera on top (well bottom) of your Blue Yeti Microphone. I have a vertical stacked monitor setup so this is the best way to keep my webcam elevated and looking at me from the side. Works great and both the GoPro style...
thingiverse
... I would probably recommend printing the ring at 100% infill for additional torsional rigidity. It works beautifully and I couldn't be happier, especially considering that it cost me $15 to make compared to $50+ for the Blue Shock Mount on Amazon.
thingiverse
I've designed this Model because I realised that the clamp that comes with most Pop Filters does not work well and adds a rather siginificant amount of weight to the mic-stand. I figured I could create something better. Tell me if you think I did and...
thingiverse
I was fed up of the goose-neck mount for my pop shield having to be constantly readjusted every time I re-positioned my microphone, so I printed a simple ring that will hold it permanently to the microphone... ...Its an added bonus that you get a little...
thingiverse
Just a stand I threw together for my Blue Yeti mic. ... It assumes you are not using a 90 degree cable, if you are there are better options.