bracket for broken trackir trackclip pro 3d models

Since I received my Ortur Laser Master 2 Pro S2 laser engraver, I noticed that the cable on the X axis was in the gap and too loose. I ended up creating a piece to hold the wire on top. ... The installation had to be easy, so I wouldn't have to take...

Keep the remaining bits in case tyou change your mind so you can reassemble your TrackClip Pro with no more damage than a couple of soldered wires. Remove the support and clean up any residue with a sharp knife or scalpel. Once cleaned up the...

Added a bl-touch mount to the bracket from https://www.thingiverse.com/gpshemi https://www.thingiverse.com/thing:4728724 Changed the design a little. Made the mounting plate a bit thinner at the mount area and added honeycombelements. ### I...

... substantial teardown of the door and it quit working after reassembly. Hopefully this can help somebody else. I know this fits great on Frigidaire pro microwave, it wouldn't at all surprise me if it fits other appliances in this product line.

... substantial teardown of the door and it quit working after reassembly. Hopefully this can help somebody else. I know this fits great on Frigidaire pro microwave, it wouldn't at all surprise me if it fits other appliances in this product line.

Wanted to install an extra hard drive into my Mac Pro but was missing the essential bracket tray. I suspect few people ever require it, but here it is! It's a bit fragile but slid into place perfectly, requiring only gentle guidance underneath.

... of the door and it quit working after reassembly. Hopefully this can help somebody else. I know this fits great on Frigidaire pro microwave, it wouldn't at all surprise me if it fits other appliances in this product line. Category: Kitchen & Dining

Remix of another design that adds the additional 4mm offset for the longer Creality Spider hot end.

US: Adapter for WiFi router by TP Link, located on the rear of the adapter are openings for routing cables downward. ...Should additional cable slots be desired, please don't delay in reaching out to me and I'll install them accordingly.

... Pin / Nut see original thing: http://www.thingiverse.com/thing:1949142 Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2 Rafts: Yes Supports: No Resolution: 0.2 Infill: 100 Notes: ABS is highly recommended for the best results.

Designed specifically for my Hayabusa, as the one that came with it was a flimsy piece of metal that scratched my screen. This mount will work on most sports bikes, although I'd imagine some modifications might be necessary. To attach the mount to...

Added tabs with holes for M5 bolts to snuggly hold the indicator. The holes are slightly undersized, so when screwing the bolt in it will(should) thread the hole, but I'd still recommend putting a nut on the other side. ... This is a remix from...

Added tabs with holes for M5 bolts to snuggly hold the indicator. The holes are slightly undersized, so when screwing the bolt in it will(should) thread the hole, but I'd still recommend putting a nut on the other side. ... This is a remix from...

This clip secures tightly around a light, enveloping it inside the assembly. While I'm not entirely confident in this setup, I'm fairly certain it would fit snugly on every Da Vinci printer, with the notable exception of the Jr model. ... Print...

I wanted to add an LED lightbar to my Ender3 Pro, but did not want to sacrifice my tool holder and/or filament guide, and there wasn't anything readily available for minimal surface mounting.I needed to cut the wire just after the switch -- which was...

... Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4769088 Print 2, 1 for front, one for rear of DX7 Pro. Has gap on top to fit remote between the dx7 pro and the underside of desk. ...

This version is specifically designed for the model "UAP-PRO", which is the Unifi Pro access point, not to be confused with the "AC" version. I removed the raised screw mounting bosses from the inside of the mount to make it compatible with the...

This holds a Skimz Quiet Pro DC Pump Controller. Specifically, the one for QP1.2, QP2.0, QPS1.2, and QPS2.0. ... Mounts to any board using a pair of screws that are M5 or fit within the M5 foot print.

A compact and straightforward single print monitor mount designed specifically for TrackIR 4, thoroughly tested on an MSI MAG271CQR display. This design necessitates only one screw to securely fasten the two components together. To attach the mount...

... PS4BracketM4.5.stl for M4.5 screws, or PS4BracketM5.stl for M5 screws. The basic configuration includes four brackets (two bottom and two top), but users are encouraged to add more brackets, especially below the console, for increased stability.

ABS 100% infill should hold PSU with one bracket. ...Please consider the print orientation.

ABS 100% infill should hold PSU with one bracket. ...Please consider the print orientation.

Mount for EZ Cam to mount to the Artist-D Pro. It attaches to four screws on the left side of the machine. You will have to get 4 screws - M4x16. ... The original screws were only 12mm long, and they did not reach The holes are notched out to allow a...

This mount moves your Ender 3 Pro Power supply off to the side to allow for a second stepper motor for dual Z axis. Need a Stepper Motor Mount for Your Dual Z Axis: Find It Here: https://www.thingiverse.com/thing:3741936 Need a Lead Screw Carriage...

This mount relocates the Ender 3 Pro Power supply to one side, making room for a second stepper motor that enables dual Z-axis functionality. ... Need a Stepper Motor Mount for Your Dual Z Axis Setup?: Check Out:...

I simply attached a small phone adapter right onto my Mavic Pro drone's remote controller, so now I can keep using my phone snugly inside its protective case without ever having to take it out.

Quick rough and ready design in Sketchup..I am sure many can do far better This is the bracket that hangs the earpiece on the headbanc. The little pins and the connector bar on the top are goign to need filing/ trimming with knife to fit the...

This is a bracket I designed to attach the stock extruder in a direct configuration. It does not require any irreversible modifications to be made to the extruder or printer. You will need an extension cable to make this work. This is barely...

This is a bracket I designed to attach the stock extruder in a direct configuration. It does not require any irreversible modifications to be made to the extruder or printer. You will need an extension cable to make this work. This is barely...

The taillight cover on my scooter is already housed within the mudguard, and the lower mounting points need to be slightly longer than those found on the michal9294 bracket to clear the rear nut cover. ...To ensure a secure fit, I highly recommend using...