bracket for broken trackir trackclip pro 3d models

The broken axle was swiftly swapped out for a brand-new, two-part replacement model. To ensure proper alignment, I printed the object twice and carefully positioned each print within the tape roll, alternating between the left and right sides. ...A...

I remixed the Creality CR10s Pro Extended fan shroud (40x20mm fan) by plammers (https://www.thingiverse.com/thing:4814295) and my bracket is a perfect fit with it. *** You can use the stock one. ...Just use some washers/spacers to fill the gap ***

Carefully thread the four inch zip ties through the bracket extension, from front to back, so both ends of the zip ties face the rear of the machine.  Position the cable and pull the ties tight. Trim off the tag ends. ... After re-levelling the bed,...

... design is pretty stupid, so you must put something in place or you will invite tons of dust to settle inside the unit. Note: you can use Ultramatch Pro SRC2496 to cancel SCMS "protection" in digital to digital audio recording (DAT/CD/Minidisc).

I downloaded an Eero pro 6 vertical wall bracket from LukeSkymaker, but it was going to take nearly 2 days to print at 100% infill. I removed most of the backplate and got it down to just over 1 day while keeping most of the functionality. ...

My Logitech G433 was broken on both Pivot Points, but i can't find Spareparts for the G433 :-(. Here are my printable Spare Part's ;-) You need: - print all four Parts (two Left, two Right). ... - 8 M3x8 Screws - 8 M3 Nuts - T5 Torx Screwdriver...

The square opening in the bottom of a clamp fits the Dwarf II tripod, and also a quick release mount 42x42x9mm for tripods. The side opening allows to charge wit UCB-C. ... The file STP is included in case somebody want's to adapt the clamp for...

Designed for the Simucube 2 Pro R2 - Single 480W PSU. ... Fasten to profiles with M8x16 countersunk bolts.

The fans in my Powerextra triple charger for DJI Phantom 4 Pro batteries started to fail, and was frankly not sufficient for safe cooling to begin with. Link below to the exact item I have, though I suspect any of the same looking blue chargers would...

He designed this to be a replacement for that broken piece (using Tinkercad). Works fine in PLA, though PETG is probably better due to outdoor use. That said, the piece fits internally into the tube so it won't be exposed to much UV...

Really like the smooth fang duct design (shown here) https://www.thingiverse.com/thing:3091560 I use it on my Creality Ender 3 with a bracket i also found on thingiverse (shown here) https://www.thingiverse.com/thing:3419869 I also own a TronXY X5SA...

The sun cracked the original top plastic piece. ...I designed this part to be glued over the broken plastic

This is a copy of the wooden card tray dividers included with the Broken Token Terraforming Mars organizer.

I used white letters on army green for the “P” side and Red letters on gray for the broken side. I created the files in TinkerCad. I stacked all four parts together in one stack. Then without moving anything anything I would delete 3 parts and export...

The stock bracket that holds the filament sensor is not so good. Sensor kept moving and stopping my prints. Designed this new one that combines it with a piece of bowden tubing to guide the filament in one piece. Sensor fits in there very snug. ...I...

The original Pi Camera mount from the website (octoprint) does not fit the bracket on the Ender 3 Pro. I made the slot wider (2.5 mil instead of 2) and added Two (2) slots to the bending arm. These slots serve a purpose and allow the user to install...

This small bracket helps reduce the wear on the x axis stepper motor wiring on the Ender 3 S1 Pro. Without it, my wiring is too short and the plug pulls out at full z height as shown in this review video https://youtu.be/zEVVV3jDUX8 Simple print and...

This small bracket helps reduce the wear on the x axis stepper motor wiring on the Ender 3 S1 Pro. Without it, my wiring is too short and the plug pulls out at full z height as shown in this review video https://youtu.be/zEVVV3jDUX8 Simple print...

I created this bracket to keep the MacBook Pro power supply off my workbench and organize my workspace more efficiently. It also protects the power supply from being knocked off the bench or table, which could result in it crashing to the floor.

---- When I ordered my Ender 5 Pro, it came in with a bent Y axis belt bracket. Upon doing research, I found that this is a common problem, unfortunately. I was told to bend the metal bracket back straight, which I did, but it wasn't as good as the...

My connector broken apart in the first try to insert, then I made a new one that could be inserted on the original model.

Just a quickly designed bracket to mount both PSU's to an alu-profile, single hole for 8mm bolt so should work on most profiles. ...

Keep in mind this is for appearance sake only and it will not have the strength of the original to control the direction of the tank when operating it with batteries. This gun is not hollow light the original, it is solid. I printed mine in resin. ... ...

I found when installing the Bracket ti the Post there was 2 notes at the rear which didn't fit into the chassis rails and was causing the bracket to bend when I tried to install and finally broke. So I expanded the brakes and added a recess for the...

I made it beacause one of my adjustable table legs have broken, with this support the broken leg will match the right height. You can print it in Petg with a 0.3 mm layer height, 15% infill and it will support with no problem all the weight of...

Frame mounting bracket for the X- Axis so I remixed the one by mechanic0 just for this. His original bracket works well for the Y-Axis. I also thinned it out since it was unnecessarily thick. ...It's not pretty but it's functional.

My Logitech G433 was broken on both Pivot Points, but i can't find Spareparts for the G433 :-(. Here are my printable Spare Part's ;-) You need: print all four Parts (two Left, two Right). 8 M3x8 Screws 8 M3 Nuts T5 Torx Screwdriver small Phillips...

The mounting bracket features strategically placed 3.5mm holes, perfect for securing screws and ensuring a stable base. ...I employed four of these brackets to attach the printer to a wooden board, effectively doubling down on stability and performance.

... misalignment. ...I have modeled this as mine had misalignment that was not solved by shims. This bracket offers 4 mm of slots for motor. My Z axis glides like butter now. 0.2 mm. No supports required. !! ...MAKE SURE TO ROTATE MODEL PARALLEL TO BED !!

So this bracket fits the stock Cr-10s Pro V2 dual gear extruder and stepper and situates it directly above the stock hot end. Ive found that if you use just the hot end's ptfe capture nut (so not using the capture nut on the extruder) , it works...