bumblebee 3d model

I recommend using a shorter heat sink and/or a fanBe sure to choose a fan size that will not interfere with the height of your heat sinkFilament sensor fits without issueBondtech extruder fits without issueOnly other fitment issues I have heard have...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

What fun! To build an adapter to your requirements, install Blender v3.80 (or later) and open the T2M42atapter_pre_assembly.blend file. Select menu View | Front (or press number [1] key on the keypad) to view the model from the front against the...

Refer to the pin diagram below.Connect the SMPS OUT- to a ground pin on the RPi.If you're using the fan, install it on the lid.Connect the fan's power and ground wires to pins on the RPi. My 5v fan was a little on the loud side so I used 3.3v and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_rotation = 0 custom_top_port_corner_resolution = 8 custom_right_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_x_size = 30 custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30...

The one thing most existing models seem to be missing is the funky characters on the keys. I looked around and found a font that looks just like what they used (basically an old computer font like the one used at the bottom of checks, ...) As I...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

The model was inspired by [this map pocket on Amazon](http://a.co/5P0dMfJ), but larger and with more holes for the bungee cords. ...I have no affiliation with this product and my design was done by hand, so please don't sue me if that's your map pocket...

The parts I used: * 30mm M3 flat screws: https://smile.amazon.com/gp/product/B07NWL5HK3 * 16mm M3 hex screws: https://smile.amazon.com/gp/product/B014OO5KQG * M3 nylon lock nuts: https://smile.amazon.com/gp/product/B07GNXDQJZ * 20mm CR-10 springs:...

I have since printed out another model in ABS which I am hoping will be more durable. PETG would be another more durable substrate to consider using. Special thanks to Jim Harmon at Keystone College and Emmitt Zugar at Salem Community College for...

I downloaded and printed two of the Flugzeug Halter - Breit STLs in the Model Plane Ceiling Hooks thing from dschiedsch. They worked but were a tight fit for some planes when I tried them out. That is when I decided to make something adjustable to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

While it worked okay for most things, there came a time when I was trying to print a model with steeply overhanging points and the stock cooling just wouldn't cut it. I designed this adapter to allow a standard 5015 radial fan (24 volt, 0.1 amp) to...

See the link below for a model that looks like the one I have. If I didn't have the laser boresighter, I would have chosen a cheap laser pointer in the $5 range or a cheaper boresighter in the $15 range. Perhaps I would have simply purchased a...

This model is only to demonstrate the principle, not to resemble the original (destroyed) or replica (Deutschen Technikmuseum, Berlin, Germany: https://sdtb.de/museum-of-technology/exhibitions/1256/). This is an improvement of <a...

I restarted from scratch and designed this model from those other inspirations. This version allows a 5015 fan to be installed without interference to the left or right gantry positions. I placed the fan above the slightly relocated CR Touch...

That way you don't need any supports. 3 perimeters 7 bottom layers on the cap ( definitely overkill ) 4 top layers Gyroid fill pattern ( any pattern will do ) Extra perimeters if needed was checked Seam position Rear ( make sure the hinge potion of...

Make the adjustments, render the desired  STLs and print it! The models are in the position, they should be printed. No support is needed. ...I suggest to use a 10mm brim for the tube to prevent it from detaching from the buildplate while printing this...

This thing is a two-part shield for the head of your Ryobi trimmer, model number: RY40220. It’s a bit crude, and I planned on making it look smoother, but this thing really works! By narrowing the gap that the grass can fit through and diverting it...

Make sure you select your arduino model and com port. Extract the files There is a marlin.ino in there that you should select Then upload to your Ramps board and it should work, I'll test the sd card and lcd when I get the bits. I would definitely...

...More importantly, Thingiverse hasn't run their customizer queue since Jul 10, 2020 so until they fix that issue, you will have to install and run OpenSCAD (free software) on your own computer to process the code to create your own customized models.

These models come with an unsupported and presupported version. This Bundle contains the following: Dr. Balthazar Morris Gideon Morris Gravewalkers Gravehounds Medical Carriage(Free in the welcome package for Patrons!) DnD Datasheets DnD...

READ BEFORE PRINTING!This is a non-commercial print, this means you are not allowed to sell files or prints of this model.______________________________________________________________________________________What is this?A modular tripod/handle...

If you need help or want something scanned, send me a message here on Thingiverse or on my FB page and I'm happy to help, ESPECALLY for a good cause (charities, educational models, STEM stuff for kids, etc.). Tips work...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_x_size = 30 custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30...

I first encountered the idea for this type of robot in a biomedical article, presented as a potential new candidate for exploring the human colon due to its simplicity and ability to navigate confined areas....

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...