bungee jumping stl 3d models
286103 3d models found related to bungee jumping stl.grabcad
Not a valid Egg Drop Challenge entry, so I only printed 1 meter of rope segments to demonstrate proof of concept.------------------------------My 10-year old son suggested a solution similar to bungee jumping. While it may not be in the spirit of...
cults3d
bungee for flexible mouse cable you only need to buy glass suction cups to make it adhere to surface
cults3d
What is a bungee? ... the bungee is a device that makes sure your mouse cable doesn't get tangled, I hope you like it and that it serves you This bungee was built on the basis of others, and this came out I hope you like it
cults3d
This listing is for a Monster model with a key ring or pendent hoop it is a STL instant down lode file for printing on a 3D printer. This is made for filament printing but could be printed on a resin printer. we would love to see what you make...
cults3d
10mm - Length 100mm Øext:40mm If you want a string with several colloris click on the following link: https://amzn.to/2GTQw8l Have a good time I present to you my last creation, this is jumping rope . ... Dimension are: ØInt.10mm - Øext.: 40mm -...
thingiverse
... table. ... The Horizontal Expansion setting is important for the screw and the base. You can scale the arm.stl down a bit for a loose fit. Every thing prints great without support. If you have an idea to improve the bungee then write a message!
thingiverse
Instructions These Files Have Been Revised Current files are named Final Bungee Hook.stl and .sldprt I'm sorry for any confusion, the revisions are as follows: 1) Part is now symetrical, the wall thickness is the same on both sides The teeth that...
thingiverse
Bungee cord wraps. ...There are two sizes one for 3mm bungee and one for 5mm bungee cord. ... Insert the cord through the bottom hole.Tie a knot and push it into the cylinder.
thingiverse
3D Printed Mouse Bungee that uses two 8mm ball bearings. ...Works better than my Razer Mouse Bungee in my opinion https://giphy.com/gifs/SsCrBfNrxa4PLUNDJf/html5
thingiverse
... test it with my mouse and it works so far. The feet is placed under my mouse mat and it works. In next version i will make it so the cable can be attached on the feet part. UPDATE 2021-02-22 - Added a stiffer version of feather = Feather_v1.STL
prusaprinters
... for desk. ...Added STL for people who want to edit this.Print Settings0.2mm, Brim, 80% infillNotes:Rotate 220 degrees on the Y axis so the top of facing the print bed. Printed with brim on. ...Recommended to print with high infill for weight.</p>
thingiverse
2-part mouse bungee dedicated to a 17mm thick desk. ... Print on flat surfaces using supports
thingiverse
Mouse bungee This bungee work with a 19mm tickness desk, He is compatible with a 3mm mouse wire (most mouse are 3mm wirered) reso 0,2mm With support infill 30%
thingiverse
End pieces for making bungee cord wraps. ... Print it with brim, support is not needed. Use a 4mm bungee cord, tie the ends with a knot and pull the loop into the hole of the ball. ... diameter = 25mm
thingiverse
This bungee has 4 holes in the base for put some neodymium magnets, then you can put a magnetic sheet under your mousepad and the bungee will stay fixed to the mousepad.
thingiverse
Hello! ... Another one mouse bungee. I was inspired by this bungee (https://www.thingiverse.com/thing:2832887) and made a new one for me. ... Also, the fusion 360 project file included.
thingiverse
Bungee Keeper measurements are 24mm (L) x 11mm (W) x 16mm (H) with 4.4mm screw hole.