bus pirate 3d models

Case for the Sparkfun Bus Pirate by Dangerous Prototypes

A simple case for the Sparkfun Bus Pirate. ... Based on a case of a similar design for the Seeed Bus Pirate. ... Instructions Best printed with 3 perimeters, 0.4 infill, 0.2 layer height.

Case for the Sparkfun Bus Pirate by Dangerous Prototypes Print instructionsCategory: Electronics Summary Case for the Sparkfun Bus Pirate by Dangerous Prototypes

A case for the Dangerous Prototypes Bus Piratehttp://dangerousprototypes.com/docs/Bus_Pirate Fits the Bus Pirate v3.6 (possibly other versions but untested) Used 1/8" thick acrylic for the top/bottom, 3/4" long 4-40 screws with nylock nuts. ... Matches...

A case for the Dangerous Prototypes Bus Piratehttp://dangerousprototypes.com/docs/Bus_Pirate Fits the Bus Pirate v3.6 (possibly other versions but untested) Used 1/8" thick acrylic for the top/bottom, 3/4" long 4-40 screws with nylock nuts. ... Matches...

This is a derivative of the following Bus Pirate v2 caseshttp://dev.thingiverse.com/thing:1716http://www.thingiverse.com/thing:2135 Instructions Print, place board in case. Seems to be that if you place the probe set on before the top you have an...

Wanted a case for my SparkFun Bus Pirate with a lid but no vitamins so here is it. Screw-less press together base and lid with cable entry points and led window. Partially parametric. ... Instructions...

Caja para contener la placa electrónica "Bus Pirate" versión 3.6 de sparkfun.com. Las medidas están optimizadas para imprimirlo con capa de 0.4mm. pero podeis bajaros el fichero fuente que está hecho con el OpenScad para ajustar cualquier medida. La...

2 part box for Bus pirate v4

Case for the Bus Pirate 3.5C. ...Hole in top for two headers and four LEDs. PRT files are Siemens NX7.5 files. Instructions Print. Clean up as needed. Slip Bus Pirate into case. ...Snap top on.

... bus pirate box, this one made with openscad and a makerbot. ... Instructions if you want to regernate the .stl files edit the open scad source to comment out and uncomment the calls bus_pirate_lid(); and bus_pirate_box() to get one or the other.

It is designed for the 3.6 version of the Bus Pirate but will probably accommodate other versions. It is just about as small as it can be, snug but should not require forcing in. As with all printed parts you might need to slightly adjust things...

Just your basic sandwich case for a Bus Pirate (From Dangerous Prototypes) version 3.6. The base is beefy, 5mm thick, and the holes in the base are sized to be tapped for M3 screws. ...Should sit safely on a desk while working.

This is a case for the Bus Pirate v3.6 or v3.6a. Several of the cases I have come across did not either enclose the board or did not fit the board well. No supports are needed. Snaps together. ... Note: Can use 4x 3mm acrylic rod as light pipes for the...

This is a case for the Bus Pirate v3.6 or v3.6a. Several of the cases I have come across did not either enclose the board or did not fit the board well. No supports are needed. Snaps together. ... Note: Can use 4x 3mm acrylic rod as light pipes...

I needed a case for my old Bus Pirate v2go, and decided to design a printed version of [this](https://www.thingiverse.com/thing:1716). I just loaded the dxf files in Fusion 360, and re-drew them. I also verified the measurements, adding a bit of...

Based on the laser cut Bus Pirate case. Seeing as I didn't have a laser cutter but did have a Makerbot I decided to print one instead. Instructions If you are printing this from anything other than...

An enclosure for the V3.6 Bus Pirate. ...Fits together with 4 M3x12 screws (and corresponding nuts).

Case for the Bus Pirate v4.0 manufactured by Seeed. This case is based on the series of cases by Gatsu. ...Print Settings Printer: Prusa I3 Steel ...

This makes the Bus Pirate feel really heavy. That's a good thing, it feels like a tool, now. Not a toy. There are labels for all of the signal lines, and there are holes that match up with the BP4's (non-standard) PCB hole positions. This prevents...

Laser cutter plans for a Bus Pirate 3.6 Case. Fully provided files .ai and .svg as well as generated gcode which may not be usable for your cutter but I figured I'd include them anyways. The outer box is exactly 4x7" so that you can confirm scale of...

This makes the Bus Pirate feel really heavy. That's a good thing, it feels like a tool, now. Not a toy. There are labels for all of the signal lines, and there are holes that match up with the BP4's (non-standard) PCB hole positions. This prevents...

This enclosure was modeled using OpenSCAD. The model is partially parametrized, meaning you can adapt the parameters given at the start of the file and an enclosure will be generated to fit your inner volume, holes, material thickness etc. The script...

Designed a case to keep my buspirate safe.

This is an almost closed case for Sparkfun's BusPirate Version 3.x As I need just two but very long wires I would not use the available standard adapter plug, but the cable of standard plug should fit in the designed gap.

This enclosure was modeled using OpenSCAD. The model is partially parametrized, meaning you can adapt the parameters given at the start of the file and an enclosure will be generated to fit your inner volume, holes, material thickness etc. The script...

This is a remix of https://www.thingiverse.com/thing:4848391/files Hole for bootloader connection removed.

Bus pirate enclosure - printed PETG and gives a window to status LED's / cable connector and usb connection. ...

Bus Pirate: http://dangerousprototypes.com/docs/Bus_PirateRepo on Github: https://gist.github.com/foosel/5759923Originally hosted here: http://www.thingiverse.com/thing:102133, now migrated for good

SummaryWanted a case for my SparkFun Bus Pirate with a lid but no vitamins so here is it.Screw-less press together base and lid with cable entry points and led window. Partially parametric.InstructionsPrint and press together, no screws required. ...