cable splitter 3d models
96205 3d models found related to cable splitter.thingiverse
Headphone cable splitter for approx. 5 mm cables. ... What you need: 4 x M2 x 6mm self tapping screws round head
thingiverse
For my new indirect GU10 lighting I created a y-cable-splitter. So I'm able to hang together several light spots. ... Dimensions: - height: 20mm - length: 60mm - width: 40mm Used cables: - 3-pole cable, diameter 8mm - light spot cable, diameter 2mm Used...
thingiverse
** Original Summary ** This is a remix of https://www.thingiverse.com/thing:4270737 (Basic project box) that I used to enclose a coax cable splitter that is outside. This particular splitter is a one-input, four-output (-7dB) splitter. I added...
thingiverse
If you look at the first picture, you can see the cable sheath from the brake lever entering the single hole on the left, and 2 brake cable sheaths leaving on the right, one for the left-hand front brake, one for the right-hand one. This bit's...
thingiverse
This cable housing was used to hide the solder connections between a 4 conductor mic cable, and a 2 conductor mic cable (Mogami 2534 to 2549). One half is slightly taller, so you can situate your cables in that one before putting the lid on, which is...
pinshape
This cable housing was used to hide the solder connections between a 4 conductor mic cable, and a 2 conductor mic cable (Mogami 2534 to 2549). One half is slightly taller, so you can situate your cables in that one before putting the lid on, which is...
thingiverse
Passive splitter. Parts required : 5 x thonkiconn style 3.5mm mono jack sockets 1 x 10mm M3 hex spacer 2 x M3 screws 2 x short wire pieces No supports necessary - lay top and bottom faces flat on bed. ...
thingiverse
Just print it, nothing much to say. ... Works fine with Paracord 275 and 24 AWG OCC Wire
thingiverse
Headphone cable splitter with place for passive filter - two pieces: upper and bottom. Two versions have been uploaded: 1) assembly with screws M2.5 round heads and round nuts-inserts (this version printed out is shown on pictures); 2) assembly with...
thingiverse
Main reason for making this thing was need to unscrew sensor , test its condition and put it back without need for modifying main cable ( bus). 3pin terminal is 15x7.5x10mm in size. ... If you like it or need modification feel free to leave me...
prusaprinters
It takes 3 heat set M3 inserts and 3 M3 bolts. Print instructionsUnassociated tags: Aquarium Tubing, cable loom, wire harness, wire loom, y splitter Category: 3D Printer Parts Summary This is basically just a Y splitter for Cable loom (the plastic...
thingiverse
This is basically just a Y splitter for Cable loom (the plastic split wire protection stuff. It takes 3 heat set M3 inserts and 3 M3 bolts. Print Settings Printer Brand: LulzBot ...
thingiverse
Y splitter for DIY headphone cable. Designed for: Canare Starquad L-4E5C - 4,8mm 2x SOMMER SC-GOBLIN - 4,6mm But should be good for 3,5-6 (with some heatshrink / sanding). ... Brass inserts: M3, length 3mm Screws: M3, length 11mm Bottom part...
thingiverse
This is a mount for RJ45-Ethernet cable splitter. There are various models from different vendors in online shops that look all the same. So I guess they all fit. Both splitted ports are numbered. You can also print and stick two 9 x 39 mm...
thingiverse
Das Trichter - Design verspricht eine möglichst gleichmäßige befüllung der Gläser (vorrausgesetzt ist, dass der Splitter gerade auf den Gläsern steht). ⚠ Das verwendete Filament sollte sich mit Alkohol vertragen und keine schädlichen...