calibration cube ender 3 v2 3d models

This is a belt tensioner for the Ender 3-V2, made to match the style of the original factory knob. To install, you will need a metric M4 nut for each tensioner. ... The nuts will need to fit these dimensions: x_diameter - 6.8 mm y_diameter -...

This very simple clamp slips over the spool holder that comes with the Creality Ender 3 Neo V2 to prevent the spool from sliding off. Leaves just a little space between the end of the spool and the filament to allow the spool to spin. ... Inside...

This a mount to convert your Ender 3 V2 to Direct Drive. It allows the stock fan shroud to remain and has a mount for the BLTouch. ...It mounts the stepper sideways so that it clears the Z Extrusion so that no printing area is lost

I made some modifications to be able to adapt it to the ender 3 pro and v2 or other bed with the same chassis. ... I strongly advise to print the model with a resin printer,the model requires a lot of details in the teeth.

This is a bracket for use when upgrading a Creality Ender 3 V2 Neo with a Titan direct drive kit. ...The bracket will attach to the two offset holes on the x axis motion assembly and will hold the CR-Touch device as well as the accelerometer that comes...

My PS Eye mount for Ender 3 v2. There is no need for screws. It slides right to the main 4040 profile of the base and the camera goes on the top of the mount. ...The camera base should slide right into the top of the mount and happily sit there.

... the way, so I made this. ...It is mountable on the Ender 3 V2, and I'm not sure about the pro. Definitely not the original, though. It is made for the raspberry pi 4b. ...Thanks to https://www.thingiverse.com/thing:4665097/ for making this originally!

Fits very tightly on the lower 40mmx40mm rails of the Ender 3 v2. Provides a "shelf" to support the wires and gives you something to tie wrap to. STL file contains left and right facing brackets. ... Print both or delete the one you don't need in...

This is a divider that will fit in the larger section of the drawer under the bed of a Creality Ender 3 v2. Each segment has it's appropriate size etched into the bottom. ... Remixed to fill the entire length of the drawer, and not knock the handle...

Electrical boxes that slide into the front of an Ender 3 V2 and Pro, Designed for OEM Creality mainboard and a Raspberry Pi 4 and it has a mount for a buck converter, the lids fit a 80mm computer fan for an extra cool and quiet operation, you will...

Remixed version of the double led strip for the Creality Ender 3. Used this on my V2. Made the distance between the led strips a bit bigger to better spread the light on the print surface. ... Used the following led strip: ...

This is a replacement drawer knob for the Ender 3 v2 drawer. I suggest to print in PETG since it is more flefible and PLA will break when you push it in the hole of the drawer. //edit: Makers stated, that PLA will work without issues, thanks for...

This is a replacement drawer knob for the Ender 3 v2 drawer. I suggest to print in PETG since it is more flefible and PLA will break when you push it in the hole of the drawer. Category: 3D Printer Parts

This is a piece for Ender 3 v2 PSU ikea lack enclosure. ...I made two pieces for easy printing Print Settings: 4 Walls 20 % infill Extra part needed: 4 head screw M3 x 8 mm PS:The prototype had to be modified (as seen in the picture), I...

Just another filament guide for all Ender 3 models including Pro & V2. Looks similar to the existing guides like 3059604 from MattEllison, but this one slides smooth into place and rests flat on the top rail. To ensure proper printing you should...

Made some slight adjustments to the hole placement to allow fitment onto the Ender 3 Pro V2 as the mounting plate is slightly different. I filled in the screw access hole that was on the front too. ... Simple screw into the bottom left (as...

If you have the Ender 3 v2 Adjustable Screen Holder or the remix, and your screen is loose, you don't have to reprint the entire thing again. Print 2 of these wedges and install then on the screen posts, behind the adjustable screen holder. ...If it...

I needed a dual Z bracket for my Ender 3 V2, but without the need of extra hardware for mounting it. The only extra hardware needed is the nut for the leadscrew. ... The model is oriented so it does not need supports.

... Used the Cable Chain Management from here. ...Cudo's for this. https://www.thingiverse.com/thing:4794723 Used the Cable Management from here. Cudo's for this! Perfect and Complete Cable Chain Management Setup For Your Ender 3 V2.

This is a tool drawer for the 40x40 aluminium extrusion used on Ender 3 V2. Just remove the end cap and pop the drawer in. There is room for ten nozzles, nozzle cleaning tool, nozzle swap wrench and all the Allen keys that came with the printer. ...On...

This cable chain mount screws into the Ender 3 V2 frame with M3 bolts. I designed it to be compatible with the common V-slot covers and also to be more in line with where the cables connect. ...Make sure to print it with the square part flat on the...

This is a divider that will fit in the larger section of the drawer under the bed of a Creality Ender 3 v2. Each segment has it's appropriate size etched into the bottom. ... Remixed to fill the entire length of the drawer, and not knock the handle out...

Mounts to the M3 holes on the Ender 3 V2 X-carriage, with the same probe offset as the classic mount by Jkostenov. Fits with the stock fan duct as well as the Mini-Me V4. ... <strong>Probe offset: X-42.00 Y-10.00</strong> <strong>Thanks to...

I made this mount specifically to fit Creality Ender 3 V2 Neo. The camera I have mounted is the "Creality Camera" but you can mount any that fits dimensions. If you need it the part printed for any reason. ... Message me at through my Etsy account...

Extension feet for Ender 3 Pro/V2 with useing original rubber feet as rubber inserts. Supports needed only in place for rubber inserts. ...Use two M3X20 bolts with M3 T nuts (or print M3 T nut inserts for regular M3 nuts) to secure the feet to the 4040...

These are direct drive mounts for Ender 3 V2. These mounts are for the default hot end. One is for the default single gear extruder and the other is for the dual gear extruder. ... To install, remove the spacers of the rollers, then fix the mount...

Filament Spool Holder Extension for Ender 3 v2. You need four T-nuts and four M4 screws (I used DIN 7984 (lowhead), but You can use DIN912 as well). Also You need two threaded inserts for ultrasonic/thermal installation (e.g. ...Bossard 1052 M4).</p>

Remixed from Creality Ender 3 V2 Belt Tensioner Cover by bspoel You need a standart cheap spirit level bubble L 30 mm x R 9.5 You have 2 options, Stand V1: Simply print this stand plus Creality Ender 3 V2 Belt Tensioner Cover by bspoel and glue...

Fast print for easier turning of the factory extruder wheel for the Ender 3 V2. Designed with blender. Snug fit for the recesses of the wheel without additional fixings. The head of the crank has a recess for quick turning with the fingertip. ...

Case to mount a 16x2 LCD on an Ender 3 V2 I use it in conjunction with the LCD1602 I2c display (0.1.0) plugin on my Octoprint server Mounts nice and neat above the factory display Feel free to use/ modify