calibration cube ender 3 v2 3d models

WyzeCam mount for Ender 3 V2. Mounts to the front leveling screws on the printer. I designed it with clearance but it ended up a little tight on the base of my WyzeCam, may need to scale it up a hair if it's too tight. ...Doesn't need any supports,...

A direct drive mount for Ender 3 V2 with adjustable X and Y axis. Made it adjustable for my dual gear extruder and possibly for other upgrades. ... Important note: make sure that X end stop is triggered, if not, add some spacer or bend the metal...

Here is a remix of the Ender 3 V2 nozzle holder. 39 nozzles and a BL-Touch replacement tip can be stored in it. I removed the handle and adjusted the spacing. I also designed an organizer for screws and other small items. ...2 versions can be...

... contribution. ...:) I made a IKEA (Type: L1324, 21777) LED-holder for Ender 3 v2 that slides nicely in to the V-frame. Brims was necessary or else it popped of from the bed. ... If anyone has tips and trix to make it better, please let me know.

Just a replica of the Ender 3 V2 NEO hotend bracket I made to make custom fan ducts easier to design, dimensions may not be 100% accurate but is a good starting point when designing a fan duct or any other mod for the toolhead.

Designed to fit Creality Ender 3 V2 Neo but can be used as standard container without attaching the rails. ... 2 container sizes (mm): 135L x 40W x 25H and 135L x 40W x 40H Caution: When used on printer, keep all items below build plate surface to...

Simple little part to cover the Ender 3 V2's Z screw - the filament passes past it very close and I didn't want filament to be hit by it. ... It fits over the brass bushing and there's little notches for the screws either side.

This is a Camera Arm for the Ender 3 v2 Printer. I am pretty sure it works on other printers, but if it doesn't, lmk in comments, and I will make a version for them! Have a great day! ... copyright Ben Walker

My Ender 3 V2 Mother board is on the top layer so the fan was at the botton with little to no air flow so I made a duel fan holder to mount on the side using the 20x40 extrusion as support

Fan shroud/hot end cover for ender 3 v2 neo with lightweight fan holder for spider hot end. This one: https://www.thingiverse.com/thing:6029098 Needs 1 m3 heat set insert for the screw hole. ...Painted the "Y" design on the front red to make it...

Just a simple belt tensioner wheel redesign for the ender 3 v2 since I didn't like the default blue ones. It works with a M4 nut inside. The tolerances might be too tight in this case don't hesitate to force it inside or even hammer it a little. ...

... with the Aquila. ...I think the Ender 3 V2 has similar ones. Found the file at https://www.thingiverse.com/thing:4737883. ... It printed great, but I wanted a slightly tighter fit and I made the slope steeper to the tools aligned closer together.

This is a Snap on Holder to attach a Dial Indicator to the Ender 3 V2. It is compatible with BL Touch and helps fine tuning the bed level. ... An M5x12 mm bolt is required to attach the Dial Indicator to the Holder.

... haven’t printed yet if anyone wants to print and let me know i can adjust. ...`It should fit the screws that lock in the slots. I took the idea from this https://www.thingiverse.com/thing:2757810 design added it to this to fit the ender 3 v2. ...

Spinning Spool Holder for Ender 3 V2, using parts that come with printer Allows the spool to spin freely, preventing issues with heavier spools being unable to feed into the extruder correctly Requires a 150mm M8 Bolt, 1 M8 Washer, 5 Nuts (Preferably...

looking in thingiverse I did not find any mod for the Ender 3 V2 Neo The ones that were there were very fragile or badly finished or did not fit well I suppose it is because of the recentness of the new model so I designed the connections based on a...

... en este, se mantienen dos ductos de salida y se puede usar con el cr touch instalado. ...Print Settings Printer Brand: Creality Printer: Ender-3 V2 Neo Resolution: 0.32 Infill: 10 Filament: no pla, petg Post-Printing Category: 3D Printer Accessories

I combined this with a mount to attach it to my side rails on my Ender 3 v2. ... I installed it on the left side of my printer, you'll need to remove the 2 fronts (LARGE) screws and 1 screw at the bottom.

Updated the mounting section with a boolean cut to accomodate the z-screw brass mount, which on the Ender 3 V2 is protruding of about 1mm. Also gave slightly more room for the z-screw itself. ... Added a second design, without the z-screw protection,...

I've designed an incredibly basic PSU holder specifically for my Lack table enclosure, which accommodates my Creality Ender 3 v2 Neo. It's crude and simple but it got the job done. The design allows for mounting the PSU under the table's top surface....

A replacement knob for the belt tensioners of the Ender 3 V2. Or just an M4 knob for anything ;) Requires a M4 melting winding brass insert (see image) using a soldering iron. ... You might have to open the hole a bit after inserting the insert...

Ender 3 V2 better Motherboard Case This motherboard case has a sliding lid that is on the top of it, in this case there is enough room to fit the motherboard and two buck converters for noctua fans or anything if there is anything to update on the...

Fits very tightly on the lower 40mmx40mm rails of the Ender 3 v2. Provides a "shelf" to support the wires and gives you something to tie wrap to. STL file contains left and right facing brackets. ... Print both or delete the one you don't need in...

The existing options were to mount to the 40mm extrusion, which is blocked by the PSU on the Ender 3 v2. My version attaches to the base of the machine using two existing screws and fits under the existing cable guide. You may need 3 or 4...

The existing options were to mount to the 40mm extrusion, which is blocked by the PSU on the Ender 3 v2. My version attaches to the base of the machine using two existing screws and fits under the existing cable guide. You may need 3 or 4 additional...

This motherboard cover is compatible with both the Ender 3 V2 and the Ender 3 Pro. Check out my Ender 3 V2 Silent PSU to complete the set! My remix houses an 80mm x 10mm fan that is mounted far away from the motherboard, giving you enough room to...

They are a straight fit to stock Ender 3 v2, have cut outs for the rear screws and plate area. Bottom outside of the feet flare out to provide are bigger overall footprint of the printer for better stability. The have a 2mm insert on the bottom of...

My take on the squashball feet for my Ender 3 V2 I didn't liked the other designs on here and wanted something i could screw on instead of something that has a T-slot design integrated. For an Ender 3 V1 or Pro you can use 4x the front feet. For...

I designed the part from scratch but measured the dimensions for the attaching part of the thing from another tool holder for the Ender 3 V2 (original spatula/scraper tool here: https://www.thingiverse.com/thing:4689265). ... <b>Printing Tip</b>: I...

They are a straight fit to stock Ender 3 v2, have cut outs for the rear screws and plate area. Bottom outside of the feet flare out to provide are bigger overall footprint of the printer for better stability. The have a 2mm insert on the bottom...