cam modeling

Pichu from Pokémon improved model 2022.Sérgio CAD CAM

Pidgey Pokémon 3d model made on SolidWorks.Sérgio CAD CAM

Airplane model.made on SolidWorks.Sérgio CAD CAM

Lapras Pokémon 3d model made on SolidWorks.Sérgio CAD CAM

Gengar Pokémon 3d model made on Solidworks;Sérgio CAD CAM

Azumarill from Pokémon - improved model.Sérgio CAD CAM

Pidgey Pokémon 3d model made on SolidWorks.Sérgio CAD CAM

Wobbuffet Pokémon made on SolidWorks - improved model 2022Sérgio CAD CAM

Instructions Love GoPro, love the idea and safety of dash-cam. But GoPro is too expensive for me (losing £250 is too much) and GoPro is too big and heavy for me to feel comfortable with it mounted to my crash helmet, so I came up with this. Tip:...

Two drawings are attached showing the bore hole sizes, the depth of the counterbore, and the offset from the bottom of the wall cleat to the center of the Cam Lock. The hanger and the hanger cleat must be assembled after inserting the locking knob,...

i made a full armored fpv cam mount armored with 3mm thick surfaces and the best thing is that it has sd card and USB slot opening with secured pop up cover too so no need to take your camera out for transferring files or for charging + over pop up...

i made a full armored fpv cam mount armored with 3mm thick surfaces and the best thing is that it has sd card and USB slot opening with secured pop up cover too so no need to take your camera out for transferring files or for charging + over pop up...

Using this clamp you can mount the camera module on a ESP32-Cam board in two orientations. For 90° rotation carefully fold the flex-print cable as shown and put some foam below the camera module, then snap the clamp on. Print Settings Printer Brand:...

Attached you'll find two pieces that make up the cam cover: Fix Part - This piece will be glued to the screen and should be held in place with instant glue (ethyl-2-cyanacrylate). Be cautious not to apply too much glue, as this could damage your...

This is a precision surface cam clamp designed for securing stock on a workbench. The harder you press against it, the tighter it grips the stock, making it perfect for hand-planing small pieces by hand. The clamp is specifically engineered to pair...

My mother-in-law inherited some vintage cam-operated towel holders from the 1970s, but she couldn't find any modern replacements. The following OpenSCAD script generates a close replica of the original design, perfect for printing with no support or...

I've made this box for wallmount for a combined esp32 cam (blank camera is also shown on the picture). Not sure if all of these sold are within the same measurement, so I uploaded the fusion360 file. All parts/bodies are seperated by 0.1mm in this...

My in-laws had some cam operated towel holders from around the 1970’s and could not locate replacements.The following OpenSCAD script generates a close approximation to the original. Printed with no support or rafts.To use this grip/holder you need...

This is design to work with a the ESP32-Cam case designed by SolarGermany https://www.thingiverse.com/thing:3949787/makes Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 15 Filament: PolyMaker...

This is a sleek sleeve/cover for the Wyze Cam v2. Print it upside down, no supports are required. It fits snugly on the camera, giving full access to the back/vents/lens/sensor/IR lights. The fit is perfect - not too tight and not too loose. You can...

... from ebay. esp32-cam AI thinker 2n2222 npn with a 1k resistor for amplifications of the PWM I found on youtube. The printed one on picture with the circuit is a first version. ... https://github.com/moxl-420/ESP32cam-doorbell For full info

This is a minimalist, inside-corner mount for a Wyze Cam. Simply screw it into the wall and then slide the base of the camera into the slot. There is a space behind the mount to run the cable so that it hugs the corner of the walls as much as...

 The tailpiece is a tight fit, so a screw is not necessarily needed.The lock fits a standard cam lock opening, and the nut will hold it in place.  Careful not to tighten too much!  The lock cylinder will snap (I discovered the hard...

... shaft, then fasten it to the corner piece with two more M4 screws. Repeat this process for the '12mm cap' and 12mm shaft. Finally, attach the cam to the platform using double-sided tape under its feet or elastic bands for a less permanent solution.

Make your own surveillance camera with ESP32-CAM. Design to protect your module and keep it safe.  Faster to print, easy to open and close. Full tested and ready to be use after printed. For outdoor use, privilege PET rather...

There have been several cam rollers floating around. This one has the registration slot. Recessed nut and screw heads for a cleaner look and safer operation. Stress line eliminated or reduced by allowing the body to follow the contour or the...

I'm redoing my first car cam project. The original design was too short for the camera and internal components to fit snugly, so I ended up attaching the bottom screws of the camera to the top two holes. Although this worked initially, the PLA...

My Ring Door View Cam would not fit my door thickness so I quickly printed a spacer to fit between the door and camera to allow correct fitment. Print instructionsPrinter Brand: Prusa Printer: i3 MK3 Rafts: No Supports: No Resolution: 0.30mm Infill:...

This adapter replaces the standoffs to secure any 14x14mm micro cam in place, featuring a compact design that adds only about three grams with the camera attached. The mount also provides substantial protection for your camera. To achieve a clean...

This tilt mechanism fits an xhover MXP230 frame and a 25mm camera, such as this one: http://www.bcmultirotors.com/#!/Mini-FPV-Cam-800TV-Lines-Sony-Effio/p/46356779/category=12460379. A sub-micro servo is required; I used a Turnigy/PowerHD 1440A...