camaro sound tube delete plug 3d models
144298 3d models found related to camaro sound tube delete plug.thingiverse
Improved design of the intake plug when removing the sound tube from 6th gen Camaro 6.2L. Stays without sealant, sloped o-ring groove tightens the fit if the plug is pushed out. Works well with the firewall plug from...
thingiverse
but All I've done is given the plug some texture/grip so that it can be identified if you ever need to take it out. The hole is hard to see, I needed to feel my way to it and thought it would be beneficial to give this part a unique feel so it can be...
thingiverse
I designed and printed a plug to replace the firewall end of the "sound tube" and plugged the air intake tube with a rubber cap originally (various sources sell them as chair leg tips). Later on I made a custom cap for the air intake end (see...
thingiverse
Simple plug with '86 logo, for Toyota 86/FRS/BRZ/GT86, to delete the sound tube
thingiverse
Small device allowing deletion of the sound tube in a 2016-2023 Mazda MX-5 (ND). Only useful for manual transmissions. ... Print in ABS with supports in the main tube, but not the straw.
thingiverse
Basically it's a plug that goes right into the intake connector of the sound tube of a 5.0L Coyote V8 engine of a 2015-2020 Mustang GT to cut off the noise. I've been told that getting to the holding screw on the firewall side of the Sound Tube is...
thingiverse
This plug easily pops into into the hole left in the firewall of the BRZ, FR-S and GT86 when you remove the noise generator
thingiverse
This fits in the end of the Mazda NC2 MX5 Sound tube where it attaches to the firewall and significantly reduces the transfer of sound into the cabin. This method leaves all of the sound tube piping intact so that the purge solenoid mounting bracket...
thingiverse
I put on an Airaid cold air intake and needed to plug the sound tube and did not want to go to the trouble of removing it from the firewall.
prusaprinters
I put on an Airaid cold air intake and needed to plug the sound tube and did not want to go to the trouble of removing it from the firewall. Print instructionsCategory: Automotive Summary I put on an Airaid cold air intake and needed to plug the...
thingiverse
The Stock Scion FRS / Subaru BRZ / Toyota 86 has a "sound tube" that connects the intake to the interior of the car. When this is removed for various reasons you need to plug the hole left in the intake. This is a plug properly sized to do that. I...
thingiverse
Plug designed for the ~17mm hole in the intake elbow, commonly needed to plug the extra hole on the new intake boot when deleting the ASC throttle body on e36 or Z3. Dimensions are based off of the original hose barb, which is a very tight fit, and...
thingiverse
** -----------------------------------** There are also a couple of alternate versions of my Gen6 Camaro **V6** sound tube removal plug set (the original versions are at- https://www.thingiverse.com/thing:3127222). They are intended to improve upon...
thingiverse
Rimlock plug I made for my Honda XR100 that I use for road racing, the rimlock is just extra unsprung mass and isn't needed on pavement. This fills the hole left over. ...It could be used on larger rim locks also, by scaling it up (Scale = XXmm/8mm) ...
thingiverse
Simpel plug to cover the hole when deleting the rear wiper of a Porsche 996. Fixates using bathroom silicone or glueing a M4 bolt to the bottom. ...Super light weight!
thingiverse
I needed a replacement plug for my BigShock after removing the factory end cap so I could remove the air restrictor. This plug also takes up a bit of the dead air space inside the barrel as well. ... Print Settings Printer Brand: ...
thingiverse
... sure, cannot confirm on NB2 cars) is about 1" diameter. This plug is a .25" tall protrusion, and has a groove for a #119 o-ring for sealing against the fender face. ... Solidworks 2021 files are also included if you need to make modifications.
thingiverse
This is a sealing plug for the 5th Generation (2010-2015) Chevrolet Camaro that allows running the dual wideband extension cables of the Innovate DLG1 into the cabin via a grommet hole located in the cavity with the cabin filter without risking the...
thingiverse
This is a door plug useful as replacement of original or lost door plugs. The plugs are located in front of the door where they replace harness boots for cars without electrical windows and/or locks. I printed it using TPE (Grade 88) but you can...
sketchfab
EntryPlug in Neon Genesis Evangelion A capsule-like tube that houses the pilot in the Eva. ...sound from here
thingiverse
BMW E30 ABS sensor delete plug. ...Just reuse the OEM M6x12 bolt or get new ones.
thingiverse
Simple threaded antenna delete plug for our loved mx-5, use spacer in "trunk side" of plug for tighter fit. ...If you forgot to plug antenna hole during bodywork this is a great solution :)
thingiverse
Just a simple plug for the hole after idle control valve delete on the m54 engine. Made according to the template on the MS4x wiki. Printed from TPU and PC. Prints without any supports. ...Not tested yet on the engine!
thingiverse
This is the antenna delete plug for the 1995-1999 Dodge Neon. This part has been discontinued for some time now and I decided to create my own. ...Enjoy!
thingiverse
... this is designed to fit snugly between the edges. My guitar is an Epiphone c40, so this should definitely work for others of that model, but may also work for other guitars with the same sound hole diameter. ...(or may be able to be scaled to fit)
thingiverse
Motorcycle mirror delete plug incorporated into a GoPro mount. one less bar clamp on. An out of the way mount for a GoPro while leaving the option for one functional mirror. allows the user to remove the go pro and mount with no tools. installed...
prusaprinters
Link to the original idea here.I exclusively use either an external multiprotocol or Crossfire module on my X9 Lite so I decided to delete the stock 2.4gHz antenna. ...I cut mine to remove it because I didn't feel like soldering and either way would...