camera rail mount 3d models

I designed this thing to mount a standard 2.5" SSD on a din35 rail. It has an offset to give additional room to the side where wires plug in. I added a "pry bump" to protect the corner of the SSD during removal. ... It prints best with no supports,...

... small amount - only for the 4 SSD retainers on the plate part and under the keyed locators on the clip part. The two parts will need a small amount of glue when fitting together. The clip part could be used to make other types of DIN rail mounts.

Quick and dirty PIC Rail cellphone mount, video, Nerf Battle royale map modes, whatever you need it for. Aimed to keep it low and not interfere with iron sights. Needs M4x30ish screw, I designed it to use M4 square nuts - since that's what I have...

The requirement was to route the cables downwards and the clip for the DIN rail should be able to be opened at the bottom. The load should therefore hang from the upper notch as a rigid element.As there was no suitable solution after a long search, I...

Simple flashlight rail mount extension for an Umber Eyes (Hound Wolf, Resident Evil Village) cosplay. I needed the flashlight to be slightly further out from the handguard to avoid hitting the 45 canted iron sights and PEQ. ... Feel free to modify as...

Here is a remixed bracket that I put together to allow me to install the Hermit Crab on my top-mounted linear rails. To install the bracket, you need 4 x M3*6 screws. You need 3 x M4*12 screws and nuts and 1 washer. ... I used tree supports only...

I initially created it to replace a damaged rail that securely mounted my 1x red dot scope on the Celestron 8-inch telescope. If your telescope's outer diameter significantly deviates from this standard, you will likely need to adjust the tubedia...

Simple little rail attachment for scope. ... ID: 19.05

It's meant to be used with a DIN-rail stand which can be found here: https://www.thingiverse.com/thing:3690627 You can mount the PCB in two different orientations as shown in the renderings. ) Mounting option #1 is the default setup. This should be...

I prefer the USP 45 Site Mount but I needed something that fits my .40 Beretta PX4 Storm, so I rebuilt it from scratch in Tinkercad to let me make changes where necessary to fit my handgun. I added three rails and an extension with a bottom rail on...

I added three rails and an extension with a bottom rail on the front end as part of the print. I cut the hex holes for the screws to fit a 6/32 machine screw I bought at the local hardware store. If you want a different screw size, feel free to...

A DIY solution to mount things on a din rail. You get the body and the attachment that create the entire "build". So what you are doing is merging the attachment to your Arduino enclosure and printing it. After that the entire thing just slides onto...

This is a rod holder mount to attach to the "Yak Attack" style rails. This mount works with both the Scottie and Berkley holders. I got the base section from someone on here, but can't remember where, so if you recognize it, let me know and we'll...

This is designed for my Ratrig VCore3 I have attached a dimensions file for the Din rail - you need to cut out the ends to fit with a hole in the middle or alternative drill a hole in the middle up to you - but no matter what the rail does not fit...

Hello, I present two models of riser rail for airsoft and asg replicas. The taller one is 31.50 mm high and the other is 21.50 mm high. ...To connect them I used 4 M8 screws, 35 mm long, and 4 nuts.

I'm attaching a custom rail attachment to my Caliburn, which will hold either a flashlight or a laser. The design is based on this existing model found online at Thingiverse (Thing 2376150). ...It's specifically designed for the Caliburn frame and...

It attaches to the picatinny rail system, fitting neatly under my scope, which is great because that's all the rail space I have. I'll upload some photos when I finish it. ... It was specifically designed for a rechargeable flashlight you can find on...

Model based on what's mounted on my SP-3. ...Will be probably further used to model whole printer.Included both mesh and F360 project file.

A custom-made din-rail holder designed specifically for the Lata Panda device.

This part can secure din rail to any flat surface with M4 or M5 screws.

This is a base for all my rail tools - upgrades. ... Remix it at will, it works.

This spring-loaded mounting assembly attaches an Arduino Uno to a standard 40mm DIN rail. It can be quickly attached or removed by pulling back on the Slide Bar with a flat-blade screwdriver. The spring-loaded design holds the assembly rigidly to...

The rail and mount are attached to the camera housing baseplate via a 1/4-20 2.5" stainless steel bolt and recommended washer. The position of the trim weight can be adjusted by loosening the bolt and slide the rail forward or backward. I've tested...

This is to hold the rails in kitchen cabinets. ...This specific type I could not find in stores.

Rail for Ulefone Armor Case, I made this to replace mine that broke, hope it helps some one

I remixed this so that it'll fit the thinner rails on the CR10 for the Y axis

I employed this blueprint to seal a gap within an electrical enclosure. ...It proves effective for French rail applications.

I've designed a minimalistic stand for the Raspberry Pi camera to use with my Creality printer.This mount uses a knob connection that is used in the Pi camera case in:https://www.thingiverse.com/thing:3121052/remixes

By providing a stable and secure platform for these accessories, the VZ61 AEP Jing Gong optic rail enables shooters to quickly acquire their target and engage with precision. ...Whether used in tactical applications or competitive shooting sports, this...

This is a Nest camera mount that attaches securely to the X Rail of your Lulzbot Taz 3D printer. The Nest cam snaps into place within the ring, while the X Rail bracket can be positioned in various spots according to your preference for viewing your...