camera tripod screw 1 4 20 tread 3d models

A GoPro camera tripod mount in the 1/4-20 size is available for purchase. This simple yet essential attachment allows you to securely fasten your GoPro camera onto a standard tripod. ...The 1/4-20 size ensures compatibility with most tripods on the...

1/4" screw used to mount a camera onto a tripod, specifically designed for customized use with tripods. Customized version of the original screw and nut generator found at http://www.thingiverse.com/thing:193647, created using Customizer! at...

Perfect replacement part for standard tripod thread mounting hole, designed specifically as a temporary solution when authentic nut cannot be located. I opted to use this modified version for my iPhone 5s tripod attachment accessory. Please ensure...

The mount features a standard 1/4-20 thread, allowing for effortless screwing onto any tripod. Printed with PLA at 35% infill and without supports, it achieves an optimal balance between weight and strength. A hidden Easter Egg is cleverly integrated...

I'm on a mission to get the perfect shot with my Anycubic Kossel and I need an adjustable camera holder that can accommodate a standard 1/4 inch screw. ...The current setup is a bit shaky, but hey, it's just the beginning - this is version one after...

... tripod attachment point for Sergey_77's camera adapter. ...The thread in the original was the wrong size for my needs, so this is just a resizing to the 20-1/4 thread size needed for typical tripod posts found in the US, or at least in my house. ...

This mount enables you to attach a 3/8" camera securely onto the widely used 1/4-20 UNC tripod thread. ... Alternatively, it serves as an effective method to obtain a high-quality 1/4-20 thread in a model printed at lower resolution or with the thread...

A few simple 1/4-inch 20-thread-per-inch camera tripod mounts are connected to 5/8-inch 27-thread-per-inch microphone holders using adapters. ...Adapters two and three need a 1/4-20 nut inserted into each one.

Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647

Snap a 3/4-inch, 1/4-20 screw through the hole, drive it firmly into your camera or microphone, then latch it onto a sturdy painter's pole and soar above with ease! ...Video arriving next week!

You will need a 1/4-20 UNC Nut Category: Camera

... one had to be printed with 1/4-20 thread. ... Diameter: 13cm Since the thread on the ball of my Spider tripod was broken off, a new one had to be printed with 1/4-20 thread. ... Diameter : 13cm FreeVersion : https://www.thingiverse.com/dedj/designs

A crucial screw is needed for this Sony camera holster project found here: https://www.thingiverse.com/thing:2415868 - it's actually a remix I created for a buddy. ...The design remains the same in terms of height, yet it has been modified to be...

A different version of my screw I designed for this project: Lens Cap HolderThis is designed so that it can be printed lying on the print bed. ...I haven't tried it yet, but I hope it should be a bit stronger due to the direction of the force...

https://www.thingiverse.com/thing:2423960 requires a special 1/4-20 UNC nut as additional hardware to fit on a tripod. I couldn't source it locally and was wondering whether a 3d printed one would do the job. I jumped on Fusion 360 and here is the...

I Designed An Alternative Screw For This Project: https://www.thingiverse.com/thing:3516366 This Design Is Meant To Be Printed Flat On The Print Bed, And I'm Hoping It Will Provide A Bit More Strength Due To The Force Acting Perpendicular To The...

... das Gewinde an der Kugel abgebrochen war musste ein neues gedruckt werden mit 1/4-20 Gewinde. ... Durchmesser: 13cm Since the thread on the ball of my Spider tripod was broken off, a new one had to be printed with 1/4-20 thread. ... Diameter : 13cm

I crafted this modification to convert the 5/8 x 11 non-telescoping survey tripod mount to 1/4-20 by simply threading a suitable length of 1/4-20 bolt through the base. ...A half-inch length generally proves effective for most uses.

The design focuses on compatibility with vintage tripods featuring a standard 1/4-20 threaded post. To get my phone holder working, I had to expand the screw hole with a drill bit and secure it with a thin, affordable nut available at most hardware...

Nothing fancy, just a picatinny - to - 1/4-20 thread adapter. Screw it onto your tripod plate, put your scope mount or attachment onto the rail and off you go. The thread is sturdy enough to hold the adapter very tightly, provided it's printed...

Instructions Pause your printer just before the hex nut cavities are covered, insert 1/4-20 nuts, and continue printing. (This was at the end of layer 44 of 47 on my print) Screw a threaded rod approximately 4 inches into the end of the pistol...

I'm drawn to the design by jakejake for the Universal Phone Tripod Mount, but I've discovered that in Europe, 1/4"-20 nuts are not widely used. ...As a result, I've made some adjustments to the base with an integrated thread, and it's working...

This can be used to mount a 3/8" camera onto more common 1/4-20 UNC tripod threads with ease. Alternatively, it serves as a means to get high-quality 1/4-20 threads into models printed at lower resolutions or with the thread printed on its side. One...

This thing was designed with Tinkercad Edit online https://www.tinkercad.com/things/3PwPwnIfqOa Turn any tripod into shooting sticks instantly Turn your gun rest/yoke on a tripod securely with 1/4-20 nut The curved design fits S&W X-Frame and...

This can be used to mount a 3/8" camera onto the more common 1/4-20 UNC tripod thread. Alternatively, you can use it as a way to get a high quality 1/4-20 thread into a model printed at lower resolution, or printed with the thread on its side. I've...

Tripod adapter for GoPro camera. ... You need to provide a 1/4" to 3/8" converter to screw into the adapter.

A mount suitable for a standard tripod screw to affix a catchbox hub.

You'll require a 1/4-20 UNC nut for assembly purposes.

It uses the hot or cold shoe of a camera to add a tripod mount 1/4" thread for another (very small and light) camera. ...I wouldn't recommend using this with any heavy or expensive cameras or if you'll be shooting handheld as it's just a friction fit in...

My first usable thing made with my new awesome Prusa MK3S+ :-) The MK3 at 0.1 mm makes perfectly good thread, that easily fits the tripod mount bolt. ...(¼-20 UNC)Other mount designs require a ¼-20 UNC nut, that is just not easily available, so I...