canon rf to sony e mount 3d models
2264607 3d models found related to canon rf to sony e mount.thingiverse
Flange distance difference from Canon FD to Sony E is 24mm, but the adapter is 23.5mm to allow for printing tolerance and to ensure focus to infinity. Adjust this in your slicer if your printer is not perfectly accurate. Print with the Sony end on...
thingiverse
... any margin. You may need to tweak the Z scale up/down by 1% or so to make it work with your printer. For reference, the Sony E mount flange focal distance is 18mm, and Canon EF mount is 44mm, giving 26mm flange to flange distance for the adapter.
thingiverse
This is an adapter to mount old/vintage Canon FD lenses to modern Full-frame or APS-C Sony E-mount Cameras. The adapter has an internal "pin" that triggers the automatic aperture lever, thus allowing you to select the aperture that you want. This...
thingiverse
A mount adapter from Canon RF mirrorless cameras to Konica Hexanon AR. The flange distance is set to allow for infinity focus. I tested the adapter on my R6 with a Konica 40mm 1.8 and it works great! ...
cults3d
I share with you my design to adapt Canon EOS mount EF lenses (5D 6D 1200D 700D 750D 800D 70D 77D 80D...) to mirrorless Sony E-mount cameras (A7 A7II A7III A7RIV A5000 A6000 A6300 NEX-3...) The design has been perfectly adapted with a Sony A7II...
thingiverse
... ...Since i worked with Canon, the angle finder C was the item to have. I recently switched to Sony but sadly Sony does not make an angle finder that fits My a7iii or a7Riv. I made an eye cup mount for the canon angle finder. ...Hope you find it useful.
grabcad
3D printable model. ...I set scale for my 3D printer Prusa: 1,011 for correct size.The lens and helicoid demounted from kiev-4m camera.
thingiverse
The Adapter to fit Tokina 135mm Lens with Om Olympus mount to my Sony A7 with E mount
prusaprinters
Canon FD to RF adapter. Printed in two parts. Wet sand with 400 grit so that you get exactly 22mm height. 3x10mm M2 screws and glue in place when all fits well. Printed in CF-PETG (Atomic filament). 3 perimeter 5 bottom and 7 top layers 0.15 mm layer...
thingiverse
This is a fully 3d printed canon RF to canon EF adapter with infinity focus, 7 degrees of tilt and 180 degrees of rotation. Always hold the lens when using it, just in case. You can use [this](https://www.youtube.com/watch?v=y1ZuK_dDweg) technique...
thingiverse
This is an adapter to allow Argus C3 lenses to be used on Sony E mount bodies.
thingiverse
A "messy" remix of two designes I found here on Thingiverse: - Sony E Mount to Minolta MC/MD/SR Mount Adapter https://www.thingiverse.com/thing:2298688 - Minolta/Konica-Minolta/Sony A Lens To Leica M Body (Techart Pro LM-EA7) Adapter...
thingiverse
Sony E-Mount adapter for telescopes with 2'' eyepiece diameter. Supports needed. Orient the part with the E-Mount on the build plate. ... Print in black to avoid light leakage.
thingiverse
This is an adapter to convert lenses that use olympus om mount to the sony e mount, it should be printed with the olympus mount facing the bed plate. ...
thingiverse
Adapter for Vintage Male T Mount Lens to Sony E Mount Camera. ... I used this on my Sony A6400, It's a aps-c camera and it worked well, but It hasn't been tested on a full frame camera yet so it's possible you may run into unforeseen problems.
thingiverse
Hey everyone i cant find a Mount adapter to the Yashica AF 250 to the Sony E-Mount so i build one of this. The only thing what you have to do is to take your best 3D Printer options and print it. But dont forget the Supports. Hope you enjoy...
thingiverse
An adapter to mount a Sony E-Mount camera body to an old Tasco Microscope. ...The part that goes into the microscope is 21.2mm in diameter, so it may fit other microscopes or telescopes.I printed this in white PLA, but that lets some light through so it...
cults3d
An adapter to facilitate large focusing helicoid on Sony E-mount cameras. M65x1mm thread -so a fairly accurate printer is required. This is a remix of one of my other mounts, that someone asked if I could do.... now with over 50 downloads! What is...
thingiverse
This is an adapter I made for 1,25" barlow to sony camera (e-mount). Remix from https://www.thingiverse.com/thing:902828 but typing it in the "remix" field bring no results (??) I re-used the locking part and made only the tube. ...
thingiverse
This is a mix of two current things https://www.thingiverse.com/thing:2794258 https://www.thingiverse.com/thing:2298626 It allows you to fit Miranda lenses to a Sony E mount. There are some very nice prime lenses on ebay going very cheap. I...
thingiverse
E-mount to 1.25" telescope adapter with locking mechanism.
thingiverse
An adapter for using the very old L39 or M39×26tpi Leica rangefinder lenses on a Sony E-mount camera. Does not have M39 threads just a gentle cone to screw the lens into. It's up to you to make sure the lens is on straight and any controls are where...
cults3d
... by the target to infinity. With this adapter it is possible to use any Miranda E-mount lens on any Sony E-mount camera (NEX) such as sony A7, Sony A5000, Sony NEX 5 or any of the compatible models. I'll be happy to answer any questions. ...Enjoy!
thingiverse
E-mount to 0.965" telescope adapter with locking mechanism. My telescope is an old BOB Optik 114/900mm reflector telescope. I had to set Clear Image Zoom to 1.3 to get rid of the vignetting. ... I highly recommend using a remote control or setting a...
thingiverse
Solid and well working construction :) ! ...WARNING ! Before you print, set the thing upside down (X axis or Y axis rotate 180°) to make the print quicker (20 min faster) and save the filament (less support)
thingiverse
Canon FD lens to Sony E infinity focus fix for full spectrum tested a6000 full spectrum
thingiverse
contax/Nikon RF Lens (External Bayonet) to Sony E-mount body adapter.
thingiverse
A simple adapter from Canon EOS RF (eos RP in my case) to a Schneider Robot Xenon 40mm f/1.9 It has some issues that I fixed "in post" as I didn't want to waste time and filament to reprint (and so miss from the model as I didn't want to add them...
prusaprinters
A simple adapter from Canon EOS RF (EOS RP in my case) to a Schneider Robot Xenon 40mm f/1.9The v2 fixes a lot of these issues:no sanding needed, it's now the proper focal distanceadded a mark for the dot and a twist lock, the body is wider tooThe...