card holder board 3d models
432277 3d models found related to card holder board.cults3d
Deck size: POKER size card (3,5"x2,5") (63.5 x 88.9 x 17.5 mm - with of card x hight of card x hight of deck) I printed up side down, without any support. Printed versions are earlier. Uploaded versions has not yet been printed. H05V-U 1.5mm2 cable...
thingiverse
Deck size: POKER size card (3,5"x2,5") (63.5 x 88.9 x 17.5 mm - with of card x hight of card x hight of deck) I printed up side down, without any support. Printed versions are earlier. Uploaded versions has not yet been printed. H05V-U 1.5mm2...
thingiverse
After printing the original one of the hinges broke off, I glued it on with Gorilla Glue. ...So I created this Remix with added support so it wouldn't break and printed it 15% larger to accommodate PLA as a hinge.
cults3d
Card Holder with double line for cards , each line with capacity for: 5 american standard cards or 4 Standard cards (MTG) or 6 mini american standard 5 spots for tokens large 277 mm width 50 mm height 19mm
thingiverse
This holds credit-card sized cards on an Ikea Skadis board. I use it for the various security passes I have. It places them in an accessible spot at my desk. ... This one is V2 with an extended base for that cards that stick out farther.
thingiverse
... type. I used different colors for each deck. I am still planning to create holders for the large cards, however not sure when I have some time available for this. UPDATE (2019/01/14): Added 3 designs with slot for discarded cards at back. ...
thingiverse
For those who owned 2nd printing ROOT Board Game onwards, you only have 1 card holders instead of 5 Use this to print your own card holder Can be used for a general purpose card holders too! ... I designed this to be used with this great insert:...
thingiverse
Scythe Board Game Card Holder I reduced the mass of this card holder by about 100g: https://www.thingiverse.com/thing:3086696 I cut the sides open, added storage holes below the cards,and reduced the walls to 0.96 mm thickness. Printed at 0.32 mm...
prusaprinters
Scythe Board Game Card Holder I reduced the mass of this card holder by about 100g: https://www.thingiverse.com/thing:3086696 I cut the sides open, added storage holes below the cards,and reduced the walls to 0.96 mm thickness. Printed at 0.32 mm...
thingiverse
I am working to resolve this issue.** **A customizable card holder for your favorite board game!** The holder has a sloped bottom to hold cards in. A "finger" cutout in front allows for easy retrieval of the entire deck. Negative space in the floor...
thingiverse
This is a set of card holders for the game Dungeon!, the D&D board game. Instructions I've been sitting on this since Jan 2013 because I wanted to print it before I posed it. Alas I haven't found the...
cults3d
... the plastic blister that holds all the components. It is very possible that this card holder can also work for board games that use cards similar to the ones Takenoko has (4.5 x 6.5 cm), if you don't mind it having "Takenoko" written on it... ...:)
thingiverse
It is very possible that this card holder can also work for board games that use cards similar to the ones Takenoko has (4.5 x 6.5 cm), if you don't mind it having "Takenoko" written on it... :) ...
myminifactory
Holds 3"x5" note cards, 16 push pins, and 4 sharpie markers. ...Uses push pins to attach to cork board.
thingiverse
This is a card holder that I made to hold your draw deck and discard piles. ...This is made for NO CARD SLEEVES.
cults3d
This is a card holder from Doc Seven's deck 77. The dimensions of the cards are 11 cm x 7 cm. The coin has a central hole underneath, to allow the player to push the cards out, all while being optimized to consume less filament. ... This way there is...
thingiverse
... lately so I decided to make a little something to make my setup and teardown of the game a little easier. ...This card holder was designed to be stackable, fit into the original gizmos box, and provide easy access to the cards during game play.
thingiverse
A smaller version of my other card holder, Scaled for the treasure deck in Talisman, Tall enough to hold all the treasure cards from the original box (Unlikely to hold any expansions) This has locating lugs so that they may be stacked. ...This has not...
thingiverse
Printed some Card holders for the new Pandemic Board Game. Added a notch at the back so it is easy to draw the bottom card. As well as holding cards they also provide a quick and easy pack away method and store perfectly in the box. Work in...
thingiverse
These are card holders/organizers that I designed to hold the cards for Star Wars Imperial Assault because it has a lot of these cards but they will also work for other cards that are roughly 40mm X 63mm. ... In the future I intend to add some...
thingiverse
These card holders stack on one another to fit the exact high of the game box. Using these to sort the cards made it possible to fit the game extension box inside the base game as well. Model dimensions are in millimeters. ...Good luck!
thingiverse
I got the inspiration from https://boardgamegeek.com/geeklist/115468/item/4369639#item4369639 You can find the following designs in the file section: - Adventure Cards - Spell Cards - Neutral with Talisman logo - The City - The Highland - The...
thingiverse
Remix of "Hadara" board game card holder from "canadiankorean". ... Better view on the card's cost.
thingiverse
Just a little holder for the cards in "Dungeon! Fantasy Board Game". ...I printed a few of these and glued them on a board.
thingiverse
This is a USB CNC Breakout Board holder, Made if for my CNC Router and Mach 3, Updated the design for 3D Printing as original was made for Acrylic
thingiverse
Card holder for board games or Magic the gathering. It has docking lugs for stacking so that you can have a discard pile above (or below) the main deck (I have yet to print a second one to test if this works). It holds firefly board game cards in...
thingiverse
Card holder designed for Descent 2nd edition, but it will hold any 41mmx63mm cards. Printed on Prusa Pro with 0.2mm layer height. ...Enjoy!
myminifactory
... this design: Dungeon Board to hold your cards in place. ... Card Display stand for Souls/Wounds. Card holders for Rooms/Spells/Hero's/Boss's not in use The box was designed to use the existing game box lid and hold enough content for 2 players. ...