castle tv show 3d models

I always have a copy of Emmett's brilliant Gear Bearing out on the coffee table - it's such a great talking point and introduction to 3D printing - and recently someone I showed it to suggested it might make an interesting bangle. I'm not sure about...

The preferred mode of dress was a belted chiton, a show-sleeved tunic, one which a heavy cloak was worn, usually around the lower body. The peplos appears to have been less popular at this time.    This object is part of "Scan The World". Scan the...

Now construction set intended to show how Voith-Schneider Propeller works. Based on attached picture. All dimensions and angles taken right from that picture, scanned and enlarged. It is not funcional model, so any other use is on Your own risk. I...

The many surviving terracotta groups showing the myth resemble marble versions, the original of which has been attributed to the sculptor Timotheus.   This object is part of "Scan The World". Scan the World is a non-profit initiative introduced by...

Size-test comparison photo shows one at 50%, two at 33%, and one at 25%. I think 50% is the most movie-realistic size, but I went with 33% which seems to be the most practical size for the scenario I wanted to use them for. ... Note that the models...

 The 3 common materials I use are PLA, TPU and PETG, so I made this switchable reminder sign to show what was last used.  I also included a ??? for other materials or for unknown if I forgot to change it. ... This will help with knowing...

... Dyson model, please report the model number in the comment section of this page. See the **Post-Printing** section for step-by-step pictures showing the removal of the broken cord holder and installation of the new one after you have printed this.

With the release of the show Stranger Things I searched all over for a real metal one for a monster campaign with friends. Since they just are so rare I opted to build one. Here it is! The Demogorgan!!!! This model is based off of the original. I...

You can then use them horizontally or vertically as I show in the pictures.The lids slide in and out easily and make grabbing the correct size lid for a container actually fun! Not much more to it, enjoy!Printing instructions:Walls: 2Infill:...

... by the material, and the clasp is reused from the original band. I have been using this watch band every day for the past 2 months and it is showing no signs of wear. ...The overall length of the watch band is 9.85in, so it should fit most people.

Pictures show orange PLA at 0.28mm layerheigt (adaptive). Use a standard m3 thread tap to thread the three unoccupied holes with minimal damage (no drilling required). There is space behind the unoccupied holes so a 10mm or 12mm screw (maybe...

Also it's SLOW, annoyingly so.The photo that is the main cover for this shows the differing heights around the edge, I went a little mad halfway through this, but as soon as I had the average height nailed it became a lot more repeatable (and fun :)...

Scale as you prefer. Print Settings Printer: Pro Mendel Rafts: No Supports: No Infill: low or medium Notes: My old printer makes backlashes and wobbles, so the models in the photo show a couple of steps. ...But I could use them anyway.</p> </p></p> ...

This detailed AT-AT from Star Wars has 15 points of articulation and show cases the interior of the machine. It consists of almost 70 parts and can be assembled without glue. The head and body had a M5 metal threaded rod for both alignment and...

... SC18 conference</a>. Here's a video showing it in action. See our Instructable for details on how it works and how to build it. You might also like our qubit spinner keychain, which was also made for our SC18 research exhibit. Category: Engineering

Stan Marsh and Kyle Broflovski from the show South Park as simple single color key chains. Their faces and hats are extruded to different heights to give them more interest than simple outlines. Both are roughly 40mm wide, 50mm tall and 3.5mm at the...

... out of TPU, and can be mounted at the top of the angled frame. This helps cushion the impact of the X axis running into the frame at the end of a print when the power to the motors is turned off.Check out the YouTube short showing the mounting here.

The photo shows an example made to fit nippers, radio pliers, wire strippers, and cutters. ...A model with nippers and radio pliers is attached as a...

... for marking the screw positions for an even easier mounting. ...Please print this at a 1:1 ratio / A4 size paper, then use to mark the position of the screws.If you like the design please show it by clicking the like ♥ button. ...Thank you!</p>

leveling is very stable at the edges,but after 5 years, the bed sag noticeable, so much the first layer shows a variance in extrusion width. Placed between carriage and heating bed. Rings (small or big) have a grove for the heating bed temp...

A simple bookmark that shows the sword Sting from the Lord of the Rings world on the outer face and which uses a fin to separate a book's pages. ...An easy, fast print.</p><p>The bookmark works best on paperbacks but it can also accommodate hardcovers...

... to be connected to a computer that takes care of the communication with OctoPrint. The display shows the general printer status, progress of an ongoing job and a minimal status during the night, including a warning if the printer is still hot.

Viewing from the bottom-up will show any support patterns to make for easy screenshots etc. Customizer enabled for this one. If both "Rotate" and "Remove_Bottom_On_Rotate" are *both* set to true, one side vanishes to further make it obvious...

... with the necessary adjustments.</p><p>You'll want to print this using a material with some flexibility. PLA won't last long. PETG results in comparable strength and stiffness to the original and didn't show signs of wear after 3 months of daily use.

... I optimized this design for my 0.4mm nozzle, so the walls are in increments of 0.4mm. *Note: I modified the STL slightly after the print shown in the photo, the model has a chamfer at the top rear where in the photo it shows a full radius fillet.

In 1925 he exhibited at the Exposition Internationale des Arts décoratifs showing Sappho, Le Livre and Masque de Bourdelle in the Pavillon du Livre. In 1926 he finally saw his Alvéar monument inaugurated after 10 years of work and a version of La...

It includes a lot of exterior detail and general cabin modeling for camera views that show the cabin from outside of the aircraft. The model is fully textured including rivet patterns. Doors and baggage compartment doors are modeled separately. This...

... nuts. I apologize that i don't know the exact offset vs. the nozzle just yet. Photo shows it mounted so the sensor is on the right hand side, but i think mounting it on the left hand side provides a better mesh and still clears the light bar.

... for it and created a solid single object. Wish I could show off the build! A friend wanted it and I didn't get a chance to grab a photo! But I plan on cutting this out of aluminum soon so we shall have few then! ... Good work to the creator!

... a standard sized battery. I've also included the OpenSCAD file if you want to customize the dimensions or make any modifications. Picture shows the adapter mounted in my MST RMX 2.0 RC drift car. ... I printed at a 10% infill, no supports needed.