celestron collimation tool for newtonians 3d models

The ZWO EAF Holder is specifically designed for use with Celestron Edge HD 8, 9.25 and RASA 8 telescopes or other similar models from Celestron's SC line. To fit the drive shaft, you'll need to carefully trim the end of the handle cap. ...This clever...

Bahtinov mask, customizable for various sizes.

Battery clip for Celestron NexStar 6SE or 8SE tripod possibly suitable for other telescopes as well. ...The battery clip is intended to hold 12V NiMH batteries, but you can also use a standard 12V power adapter.

ATTENTION! ...THIS IS NOT A FILTER, IT'S JUST THE CAP FOR GLUING THE FILTER!!!Solar filter cap, designed for Celestron Skymaster 25x70 binoculars. I used Baadar sheet filter and glued it to the caps. ...3d printed with flexible material.

Bahtinov Mask for telescopes with 110mm front end / dew cap e.g. Celestron 80_600 ED 2 Bahtinov masks, both work. Mk2 is brighter, Mk1 seems a bit more precise. I prefer Mk2 use black filament. ...Print settings: your choice.

This is a tri-bahtinov mask for Celestron EdgeHD 9.25. ...Those with smaller 3d printers should print three of 1/3 piece and assemble them together with 6 x m3 screws (or just use cable ties).

Modular telescope accesory tray for Celestron Evolution 8 The four parts I printed are Base.stl Post.stl Really Big Bin.stl 1.25 Lens Holder.stl Which took a combined 80 hours on my AnyCubic Kossel.

I recently acquired an older Celestron NexStar 8 OTA and decided to utilize the red dot finderscope from my Celestron NexStar 6SE. However, I encountered a problem as the dovetail bracket for the finderscope failed to align with the mounting holes on...

You can use standard M3 hex bolts to secure the camera (hand tighten for sure) or install littles knobs like thoses:...

Dew shield holder assembly for Celestron 9.25" Edge HD Telescope. ... Bill of Materials: * Sixteen M3 x 10mm machine screws * Sixteen 2.5 x 5mm self-tapping machine screws Optional Components: * W&W Astro dew heater strap, 100 cm in length * Camping...

This is a precision-crafted hand controller mount designed specifically for the Celestron NexStar, expertly paired with the robust CPC tripod featuring sturdy 2-inch legs. ...The revised design of the Tighter Fit model exhibits significantly less...

Solar Filter Holder for Celestron 9.25" Edge HD Bill of Materials: * 4x 2.5x8mm Self-Tapping Screws * 16x M3x10mm Screws * 1x Solar Sun Filter Telescope Sheet (Black Polymer, 12"x12") or Baader Astro Solar Safety Film (OD 5.0) Note: Use a Tap to...

Solar filter holder for Celestron 9.25" Edge HD BOM 4x 2.5x8mm self-tapping screw 16x M3x10mm screw 1x Solar Sun Filter Telescope Sheet Black Polymer 12"x12" or Baader Astro Solar Safety Film (OD 5.0) NOTE Use a tap to create a M3 thread Category:...

A remix of jamesdedij's "Holder for Celestron Nexstar Hand Controller" to suit a 40mm tube. I use this on my ARTCISE AS90C tripod. ... Could potentially fit a 1.5" tube too, particular if you scale it down to 99% but haven't tried.

Bahtinov mask for Celestron 8" HD Edge with Hyperstar V4. Closes like a dust cap. The design with a loop and a latch to more easily put on and off the halves of the mask without having to remove Hyperstar with camera. ...Can be used with or without...

Bahtinov mask to aid and improve focus on a 6" Celestron telescope.

Bahtinov mask to aid and improve focus on a 6" Celestron telescope.

Crafted specifically for the Celestron LCM telescopes, it also fits other tripods with ease. Handy for storing various items and preventing them from being misplaced or lost when using your telescope. OpenSCAD files are included for easy...

Tray to hold a TalentCell Li-Ion Battery Pack (Model:YB1206000-USB) to a Celestron Tripod with 1.5" diameter legs. Print the "test" file for a quick (comparatively) test to make sure it will fit firmly in place on the leg. Scale as necessary, but it...

Dew shield holder for Celestron 9.25" Edge HD BOM 16x M3x10mm screw 16x 2.5x5mm self-tapping screw Optional W&W Astro dew heater 100 cm strap Camping foam mat for create extension tube NOTE Use a tap to create a M3 thread Category: Other

This is a holder for Celestron Nexstar + Hand Controler that fits on AZ motorized mount that came with my AstroFi 150mm (6") Schmidt-Casegrain telescope. I had problems with the inbuilt GPS system in AstroFi, so i decided to buy the Nexstar+ hand...

This is a drop in replacement for the plastic insert of the Celestron Electronic Focus Motor for SCTs that allows it to be used on my older flat back, pre-2006 Celestron C-11 Schmidt Cassegrain Optical Tube Assembly. Under the focuser knob on my...

Reduced the diameter of the original fine focus knob design to 50mm, ensuring clearance for the eyepiece/diagonal clamping ring and standard diagonal lock screws found on the Celestron NexStar Evolution 6. The previously customized 50mm version...

The hand control base was designed for use with the 2x1 AUX port splitter connected to the Celestron HC connector. This is necessary because accessories like the StarSense camera and HC will only function when plugged into the HC connector on the...

3mm hole in the center for the laser to pass through. ...Model is 1 mm thick but I got away with only printing up to 0.8mm, will be a little flimsy.

Utilizes: OpenSCAD Wedge / Triangle by carloverse https://www.thingiverse.com/thing:1727659 for supports. (Which is an interesting take on wedges. Unfortunately, using this means that you can't use customizer.) I've marked it as a remix of two...

Designed specifically for the Celestron 114 LCM model telescope, but might fit other tripods as well. Instructions: - Print the holder - Attach it to the tripod leg - Insert your cap - Enjoy! Check out my other designs on Thingiverse for more...

Solar filter holder for Celestron 127 SLT telescope. The "ring-127.stl" should be printed twice, between which the solar filter is sandwiched and fixed with double-sided tape (with the holes on the ring aligned). It can then be mounted to the...

Thus, will allow to use it for any 3/8 mount (like the SVBONY SV225) or device (like the ZWO Seestar S50).There are two versions to the bottom part. With brass heat insert and with printed threads. Use whatever you want.For the brass heat insert...

To attach my red dot finder scope to my camera, I devised a makeshift hot shoe mount using the one from my Celestron telescope. Although it's unclear if this would work with other finder scopes, the dovetail design suggests potential compatibility.