chain link drag 3d models

Revised & strengthened version of 'Chain Link' by bqlabs: • Drag Chain : http://www.thingiverse.com/thing:397273 • Other parts that will fit the same configuration / system can be found here : http://www.thingiverse.com/thing:959297/#files Cheers,...

1 hour to design, 4 to print. The chain I started with was purchased here: https://www.banggood.com/10-x-10mm-Plastic-Cable-Drag-Chain-Wire-Carrier-Length-1000mm-With-End-Connectors-For-CNC-p-995511.html I printed in PLA, 0.3mm layer height with 20%...

The chain I started with was purchased here: https://www.banggood.com/10-x-10mm-Plastic-Cable-Drag-Chain-Wire-Carrier-Length-1000mm-With-End-Connectors-For-CNC-p-995511.html I printed in PLA, 0.3mm layer height with 20% infill, full support. In...

I needed some large drag chain and wanted an open design. I remade this into two different links that alternate which side the closed portion is on. ...I print these 4 at a time (2 each) on my Thing-o-Matic.

Cable Drag chain link, as sold on Makerparts storeSize 10mm x 15mmhttps://makerparts.ca/collections/cables-wires/products/cable-drag-chain-1-meter?variant=19172173636

Just another drag chain link I made for another project. Only bends 0 to 90 degrees (has reverse bend prevention). I remixed this while building my custom side-mounted strain relief for my Sidewinder X1. ... Nothing really special beyond that...

Remix of Claghorn's http://www.thingiverse.com/thing:611593 I wanted to change the direction of the chain to gain some more clearance, to achieve this I made this kinked link, it should be able to be inserted anywhere in the run of the chain to avoid...

I have revised the Original chain links and made the holes a bit bigger for the links to move more freely even if there are print quality inconsistencies. The original were kinda tight and have to flex it a lot of times to make it move freely. This...

 Since I am running both a standard MK3S+ and a scratch built unit with the Bear Upgrade frame, I needed to make 2 different length links, both of which are included here.Drag chain used with these...

Print in pla .4 nozzle and 0.2 layer height and enable support . ...This link allows removal of the bridge if you need to change wires around, without removing the complete chain. ...Very handy when setting up

Suggested filament to print eSun PLA+.

Here are the drag chain parts that I designed for my MPCNC Primo. ... You'll need to figure out just how many links that you will need for the size of your CNC.

Here are the drag chain parts that I designed for my MPCNC Primo. ... You'll need to figure out just how many links that you will need for the size of your CNC.

I tried printing the drag chain links from johnniewhiskey, but the links didn't move as freely as I wanted them to. I came across this remix from Yeggster and they worked much better. I needed them to fit on a 3/4" rail so I resized them. They are...

This is a remix of the "moebeast' drag chain links. This setup will allow you to install a drag-chain, without having to remove ends of cable to feed them through! Super time saver. This one .stl has 4 links 2x Right 2X Left When you install...

I know there are a ton of these already, but I needed something a little different, I added some tracking alignment links and loosed up the chain so it drop down on top of a bar let it sit lower to the machine, Also the link have a groove to snap...

A connector link for a commercial available drag chain of the make CNWSL with internal size 15mm width, 10mm high and bending radius R18 which can be found on amazon.de Example of the item:...

All credits go to kevinakasam and his Beltdriven Ender 3 mod.Link to his wonderfull mod: https://github.com/kevinakasam/BeltDrivenEnder3/tree/main/V3https://www.thingiverse.com/thing:4243512 This replaces the  1_LeftV3.5.stl with this...

On my printer the end link of cable drag was broken. So, I've opened Solid Works and draw this model for 3D Printing. ...Works great.

Customized version of https://www.thingiverse.com/thing:915487 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=915487

Customized version of https://www.thingiverse.com/thing:915487 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=915487

Prusa i3 X carriage for MK8 extr with 10mm drag chain link

Included (But not printed and tested) is the direct drive adaptor mount, link, and screw. Not needed but up to you if you wanna test it. I printed everything on 100% infill and the links I usually place ~ -0.8 to -0.9 to place the flat on the build...

Every drag chain option for the Ender 3 has a custom print head mount, so I made this to fit on any Hero Me Gen 7 platform. Comes with Left and Right configurations as well as various heights and even an adjustable option with two lengths. In theory...

The Extruder mount is used to replace the upper mount and sends the wires over the extruder so that the wires can fit into the wire claw there, but does not accommodate an X-axis drag chain. You will need 2 longer M3 screws to replace the screws...

There are (at least three) other designs here that address this same issue, however, each require additional mounting hardware: by Drazen, published Jun 17, 2015 by Antscran, published Feb 17, 2016 by 802, published Mar 16, 2016 This design...

Customized version of https://www.thingiverse.com/thing:915487 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=915487

Customized version of http://www.thingiverse.com/thing:915487 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=915487

Customized version of http://www.thingiverse.com/thing:915487 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=915487

Modelled in F360. ...Links have 30 degree (parametric) movement and KMA ends have sliding joints, so it behaves fairly realistically. ...https://www.igus.de/iPro/iPro_01_0030_0001_USen.htm?C=US