child proof door latch 3d models
98080 3d models found related to child proof door latch.thingiverse
I wanted a simple way to secure the doors while gone so I made this thingy that slides onto the bottom of the door then after closing the door you slide it over and it latches onto the door jam. It stays in place pretty well and even when they jump...
pinshape
SummaryIt was late one night and our kid was driving us crazy with the kitchen cabinet doors... I have removed the block, that was to install a baby gate on my stairs. I have attached a picture (I apologize I am art challenged). This latch uses the...
thingiverse
It was late one night and our kid was driving us crazy with the kitchen cabinet doors... I have removed the block, that was to install a baby gate on my stairs. I have attached a picture (I apologize I am art challenged). This latch uses the existing...
thingiverse
safety latch for under an oven with a drawer at the bottom fits most. don't ask about what ovens it's for. ... kept my kids from pulling out all the pot and pan lids that were stored under the oven.
thingiverse
This model also has a child proof for the lock of the knob. So your kid can't easily lock himself/herself in a room. You can still lock the door by pushing your little finger through the hole on the cover. You can fix it with a zip tie. TOU MAY...
thingiverse
... used the screw in drywall anchors) and out of reach of little ones, at any door that opens right beside a wall. PETG at 15% infill is springy enough to let the door latch and unlatch easily, but stiff enough to hold tight when tugging on the door.
thingiverse
I made a latch for the cabinet doors under our kitchen sink. The first version was held in place via friction. It took my 11 month old 2 days to get it off. So I designed a part with sliding bars. I may design it again with springs. ...I'll probably...
thingiverse
After this the inner sleeve goes into the outer one and push it on the 8x8mm shaft of the door with the nut/grub screw facing upwards. Tighten the grub screw. Attach knob or handle with four 4x35mm flathead screws. Ready to try it out. ... If you want...
thingiverse
This is an add-on to the dog proof latch to make it more stable with doors that have large gaps between the floor and bottom of the door. It has a spring on the bottom to wedge between the door and latch. It also has an extra lip on the door side of...
thingiverse
**Solution Design Criteria:** * Slip-on, slip-off easily - no removing/replacing screws for installation * No damage to door or finish * Downward pressure on lever uses door jamb to prevent handle rotation * No restriction on upward lifting of lever...
thingiverse
Couldn't find anything to fit my door knobs (schlage) nicely, so I made these two. ...One for the exterior door's knobs, and one for the bedroom door's knobs
prusaprinters
Couldn't find anything to fit my door knobs (schlage) nicely, so I made these two. ...One for the exterior door's knobs, and one for the bedroom door's knobs Category: Replacement Parts
thingiverse
This is a Remake of https://www.thingiverse.com/thing:273717 and works better for me. ...Print with PLA, does not work with ABS
thingiverse
... milk remarkably well. ...But there's often a puddle left behind when he does it. So my thirteen-year old created this, based on a child-proof safety lock. ...This means our toddle can't open the milk himself, and hopefully that means fewer messes.
thingiverse
This is not really child proof but it is a good preventative. Instructions i printed this at 20% infill and at .3 layer height but print as a solid part and at .1 layer height IF you need that much...
thingiverse
This is a child safety lock / latch meant for use on sliding closet doors, or any other overlap-style sliding doors. Both pieces print easily and quickly without supports. Installation: Very simple to install. Just use those 3M foam mounting squares...
thingiverse
Here is a simple but effective device for baby proofing table corners. The red prototype was printed in PLA but I used the opportunity to test LAYWOO-D3 wood filament to make nice corners for the kitchen wood table. They turned out very nice and...
prusaprinters
This door stop goes on the top to be out of reach from kids. ...When the door closes it blocks it several centimeters away.Version 2:* Added angles so it better fits when the door is closed* Added a curve to reduce the amount of material printed.
thingiverse
This door stop goes on the top to be out of reach from kids. ...When the door closes it blocks it several centimeters away. Version 2: * Added angles so it better fits when the door is closed * Added a curve to reduce the amount of material printed.
thingiverse
I needed a simple lock for my single cabinet doors, so I designed this in Fusion 360. It provides a simple way to safely lock your cabinets so children cannot open them. ...It is a quick one piece print.
thingiverse
Credit to FrodeEldevik for the Tri glider: https://www.thingiverse.com/thing:3392513
prusaprinters
This simple little latch blocker can be mounted on a gate with small latch.It is toddler proof*. But I believe a dog, cat or any other animal will not be able to open it as well.</p><p>For assembly you need:</p><ul><li>2x Square nut M3</li><li>1x...
thingiverse
"Child-proofing" something is in an interesting endevour. It is basically a friendly way of saying that we design a puzzle that is beyond your capabilities, that exploits your yet to develop low level of fine-motor skills, and the partial...
thingiverse
This is a two part child lock for a pill bottle. The outside of the cap is in ridged and non ridged variant because the ridges can be hard to get right and just add printing time. I had to print the inside of the cap in 0.15mm layers but thinner...
thingiverse
Lost so many of these magnet holders for 1/2" magnet to operate the hidden child proof latches. ... Print Settings Printer Brand: Prusa ...
thingiverse
Caution: This child safety latch is baby resistant, not baby proof. If your child can stand and push up, he/she can eventually get in with persistence. Also be aware that ABS layers can separate and eventually break if the baby puts enough weight...