christmas light hooks for gutter 3d models

These are take-down hooks, large and small, designed for launching model aircraft on a bungee launcher. For my Pinata or Caipi (around 1kg AUW), I use the smaller hook, while my Chimera (2-4KG AUW) demands the larger one. These versatile attachments...

Hooks for 3" spacing slatwall. These should be able to tilt in, they don't need to be slid in from the end of the wall. Works fine with PLA against reasonable loads, but if you are hanging something heavy you might want to enlarge the hook or...

My wife recently wanted pearl/bubble lights at the store when we were shopping for Christmas lights. Unfortunately, they were a few dollars more expensive than the standard incandescent string lights, which we ended up purchasing. When I was putting...

copy one and mirror it to get both hooks Works with changing table with 2cm woodpart to hook on to

I used the dragon from:http://www.123dapp.com/creature/Gargoyle-Dragon/3355535 and BLENDER for cutting out the pipe. ... Two versions: for 50mm and 40 mm pipes

It can be used for the IKEA "Lurt" [(# 003.471.24)](https://www.ikea.com/us/en/p/lurt-rack-for-6-knobs-white-stain-00347124/) rack or similar applications. ![Lurt...

Two versions are available: one for 50mm pipes and another for 40 mm pipes. Print Settings: Printer Brand: RepRap Printer: Prusa I3 Rafts: No Supports: Yes Resolution: 0.15 mm Infill: 23% Notes: I printed it in yellow PLA with a 0.15 mm layer...

There are two files- one is for a single hydroponic tower (solid, no hole) and the other is for a tower array that feeds the tower from the top (0.72inch hole in cap). ...The hole is wide enough for a tube that has an outer diameter of 0.72 inches (or...

... Best regards and print this for someone special <3 JJ Please do not sell this model, it´s not allowed for commercial use or reproduction. You only buy the personal right to use and print. If you need a finished version of it, please contact me.

I built my own version since they didn't have one available in stores. ... It also features a removable lid at the top, allowing for quick access to clear out any accumulated leaves or debris that may become stuck inside.

... were made from ABS, while the hinge and loop were crafted from a flexible filament (M3D tough 3D ink). After putting these custom hooks to the test on a mountain biking trip for four days, they performed flawlessly without any signs of breakage.

... setup, simply enter the dimensions of the pipe, taking into account the wall thickness as a negative value (-2*wall thickness). This design hasn't been printed yet, but I hope it's helpful for someone out there and also for us in our makerspace.

I've personally utilized this clever design for my trusty Netatmo rainfall sensor, but its applications extend far beyond that. ...Whether you need to install a weather station or a security camera, this mount provides the perfect hassle-free solution,...

I used the dragon from: http://www.123dapp.com/creature/Gargoyle-Dragon/3355535 and BLENDER for cutting out the pipe. Two versions: for 50mm and 40 mm pipes Print Settings Printer Brand: RepRap Printer: Prusa I3Rafts: No Supports: YesResolution:...

Battery holder for Christmas lights.The model is for 3xAA batteries. But you can easily change the dimensions in the slicer.All you have to do is fasten it with a nail, double-sided adhesive tape or string (for example on tree branches).Created in...

... it has too few possibilities to hang up its jacket. So I designed this hook for the headrest. The inner diameter for the attachment to the headrest is 1.5cm. ...Because it can get very warm in the car, I recommend ABS or PETG as material.

Snap on hooks for 19mm rod. As found on Essem Classic and many clothes hangers from Habo. Printed in PETG for strength, and because I was worried about the clip breaking with PLA. ...Might work with PLA too but I didn't try it.

Light-Up Outdoor Christmas Lantern Check out this cool outdoor lantern for the festive season. Light up your house! ... Check out my other things for a light-up star to compliment it!

To hang body washers in the shower and prevent them from being thrown on the floor, I created a safe solution without sharp hooks. These holders are designed for 3D printing using an ORCA with a 0.35mm nozzle. ...Attach them to the shower with silicone...

This is an individual hook for the gladiator system.Printed in PLA with .2mm accuracy.This is a remix, but can't remember where I got it. ...&nbsp;If you know please remind me, so that I can give credit.</p>

Thanks to the mastermind who crafted these spectacular worlds, here's a fresh remix with catchy hooks and elegant rings added to dangle from the ceiling. ...Saturn has transformed into a stunning display of eight gleaming rings, perfectly scaled for...

Screwdriver holder is a hook to which a piece of plank with holes for screwdrivers can be mounted - I used an old floor panel. ...This way you get the part faster and use less filament.My printer settings:Material : Plast-Spaw PLA 1,75 mmNozzle: 0.4...

These hooks are extremely sturdy and have an incredibly appealing appearance.

Also note, you can print the axle from the original design, scale the axle in the length axis to connect the two hubs together for added support if you printed it a little loose for your spool. If you measure it accurately, you shouldn't need the...

A collection of simple thin hooks for the honeycomb storage wall system. ...They come in lengths of 20, 25, 30, 40, 50, 60, 70 and 80 mm.</p><p>Print them laying down (just like shown in the picture), this will give them best strength.&nbsp;</p><p>I...

To attach the Twinklys to the window I have such a problem every year, the old PLA hooks break off, old screws don't hold properly - there's no room for anything.This year I got fed up and printed slightly larger, more stable hooks in PETG, so that...

To attach snowflakes from Thingiverse (http://www.thingiverse.com/derivative:44546), I designed a quick Blender template for easy printing on my ReprapPro Huxley. For hassle-free use, simply download and print the file! ...Enjoy.

Model rocket boost glider hooks, aka: xerclods, inspired by the old Apogee hooks. Which is why I originally gave them the tongue in check name "Perigee hooks". Print out two. Glue one with the hook on the rear side to the pod-pod. Glue the other with...

I wanted to store my scrapers on my ARC-PEGLAGO panels for my P1P but none of the hooks I found fit the bill. Most of the existing designs were overly tall and required two pegs.To attach the hooks to the Skadis panel I used the excellent Skadis...

I rotated and cut the knob on the back of one of the hooks off so that it will print flat and with both hooks at the same time