clamp on music stand 3d models
1306622 3d models found related to clamp on music stand.thingiverse
I was presented with a broken knob for the clamp on a music stand. The bolt had broken out of the plastic. Here is my fix. The hex hole in the knob suits the bolt head,. The hex tube slides down the bolt and these both are pressed into the knob. ...
thingiverse
This clamp is designed to fix music stands similar to the Manhasset Symphony stand, where the height of the music stand no longer stays where it was set. The nut hole in the clamp is designed to work with a Hex nut Class 8 M4-.70, which I picked up...
thingiverse
This is a clamp that can be used to keep a Manhasset music stand at a required height. The hardware that I used: 1/4 X 20 wing nut, 1/4 washer, and a 1/4 X 20 1 inch long hex head bolt. This is a print in place object. No assembly required! ...
thingiverse
This is a phone stand that snaps on to my clamp (https://www.thingiverse.com/thing:3531386). I'll try to make some more accessories to for this clamp if people like it. ...
thingiverse
This Headphone Stand clamps on your desk, providing a place for your headphone. If you have any suggestions feel free to comment. ... **Note: Print screw at 97% size.**
thingiverse
Holder for tablet on music stand. ... A tablet can be very easy to store all your sheet music on. And then place yopur tablet on your music stand. My holder prevents the tablet from falling of the music stand. ...
thingiverse
Sheet music stand that snaps perfectly onto a Yamaha YPT-300.
youmagine
I got tired of my light falling off my music stand whenever I bumped it while turning a page, so I designed an adapter in OpenSCAD to keep the light clip in place. The OpenSCAD file is fully parameterized so you can easily adjust the design to the...
prusaprinters
I have printed it standing and lying on its side with no noticeable impact on the threads. I have included two different screws for the clamp. One is just a screw with a flat top, and the other has a ball and socket joint pad to...
thingiverse
I have printed it standing and lying on its side with no noticeable impact on the threads. I have included two different screws for the clamp. One is just a screw with a flat top, and the other has a ball and socket joint pad to protect the underside...
thingiverse
Simple cut and paste remix for a secure and easy to find place to put away the vive controller i have on hand when playing Elite Dangerous. ... Prints without support.
thingiverse
I was making a music stand from whatever materials I had lying around, which was 7/8 inch diameter tubing and m6, 1/4", and #10 screws and nuts. I used someone's scad file to make knobs for hex nuts that were 10 and 11mm wide at the flats. 7/8 inch...
prusaprinters
Simply slide into a music stand. ...You can place a guitar capo (or anything) and pencil holder insert on the side. Print instructionsCategory: Music
thingiverse
Simply slide into a music stand. ...You can place a guitar capo (or anything) and pencil holder insert on the side.
thingiverse
... column of my monitor stand. ... The vertical tube is 36mm in diameter so I made this clamp-on holder to fit. You will need two #10 screws and nuts to make this work. ... I printed this in PETG with 4-5 perimeters to make the holes stronger.
prusaprinters
The vertical tube is 36mm in diameter so I made this clamp-on holder to fit. You will need two #10 screws and nuts to make this work. I printed this in PETG with 4-5 perimeters to make the holes stronger. Print instructionsI printed this at 30%...
prusaprinters
The Music Stand.I designed this because I wanted to have a tabletop music stand for my xylophone.PRINT SETTINGS:Reselution: 0.25-0.15mmSupports: yes for Music Stand, and no for Music Stand-StandRafts: noFilament: Everything accept flexible filament...
thingiverse
I'm a new modeler and this is my first model; any advice would be appreciated. ...A simple stand that I made to hold sheet music. ...Scaled to 88% for printing on my ender 3 pro.
3docean
... Please, visit the model page on our website if you need any additional services. We greatly appreciate you choosing our 3D models and hope they will be of use. We look forward to continuously dealing with you. ...Humster3D Team Sincerely Yours,
thingiverse
This is a repair part for the On Stage Stands KSA7500 double keyboard stand, for the telescoping cross member. There was apparently a little plastic goody that went between the thumb screw and the telescoping rod, to clamp it to the desired length.
thingiverse
The music on the block are two 3D printed blocks that you slide together to add some spunk to life. ... Print Settings Rafts: Doesn't Matter ...
thingiverse
My son is a photographer and was looking for some clamps in my shop for holding simple back drops on his Light stand. Most clamps in my work shop are for wood projects and much larger then what was needed. So I drew something up quick in Fusion that...
thingiverse
****** https://www.thingiverse.com/hardline23/collections/clamp-on-rail-system Welcome to my SECOND released project for Thingiverse! I normally do more industrial type projects, but had a request from a few people in my circle for a well put...