clamp on shock mount 3d models
1388339 3d models found related to clamp on shock mount.thingiverse
this is will let you use any scotty mount items to be usable anywhere that you can take your clamp with you, i use this on my foldable kayak and you can find lots of scotty mount accessory on here or online that you can use on your boat or kayak.
thingiverse
This was designed as a better way of mounting a cheap generic pop filter on to a cheap plastic shock mount for a mic. It might work with a metal one, but it might require some Engineering magic (Sticky foam tape) REQUIRES DISASSEMBLY OF THE POP...
thingiverse
High fender mount for KLE/ Ufoplast kawa KX250 fender
thingiverse
Antenna (or any project) holder perfect for clamping to a deck or railing. Designed around 1/2in pvc conduit but should fit anything around that size due to the tapered hole. ...Use the screws and pad from thing:2767847
cults3d
Antenna (or any project) holder perfect for clamping to a deck or railing. Designed around 1/2in pvc conduit but should fit anything around that size due to the tapered hole. ...Use the screws and pad from thing:2767847
thingiverse
It may not work with smaller shock absorbers, however, as the shock absorber mounting point does not protrude in quite the same way. It does work fine with mine, however. I appreciate that part 7 of the design, which this replaces, is part of...
pinshape
Summaryadjustable vacuum mount clamps on to z axis. ...works great for me, no need to enclose it.
thingiverse
adjustable vacuum mount clamps on to z axis. ...works great for me, no need to enclose it.
thingiverse
Mount your Zonestar P802N 3D printer on a table by using 6 clamps and some 3.5-4mm screws. ...Fusion 360 CAD file included.
thingiverse
This acts like a bit of a rod end for Team Associated shocks. ...Great for Crawlers.
thingiverse
This is a 10mm shock absorber clamp designed for the original Kyosho Javelin buggy. ...This clamp will not fit the 2017 re-release since it comes with 12mm shock absorbers. ... This should also fit Kyosho Optima.
thingiverse
I recently set up OctoPi on my Anet ET5X printer and needed a camera mount that would work on the ET5 or the ET4 series. I wanted to be able to move the camera to multiple positions and I could not find one here on Thingiverse that I liked so I made...
thingiverse
In my case, I use it to mount smartphones for surveillance of prints and occasional recording. It clamps onto the shelves and tightened with M6 screws and nuts. ... Parts required: - Smartphone clamp:...
thingiverse
Most cheap break-barrel air rifles suffer from a different point of impact whenever you close the barrel, this allows me to avid that issue, since the scope is mounted on the barrel therefore should always point to the same place as the barrel...
thingiverse
Work in progress for a non welded on solution for holding a standard plastic strip style rear chain guard (and oil spray catcher) for older karts.
thingiverse
Basic shock mount for any microphone: - Tripod feet ending in points to minimize contact with table - Stretch rubber bands over the two ends of the mount - Put your microphone through the mesh of rubber bands at the top and let it rest on the mesh of...
thingiverse
Simple clamp i made for the inmotion v13 shock pump that holds the nozzle in place so its not flopping around while in storage.
thingiverse
This is an add-on for body post/mounts if you printed my remixed long travel shock mounts/hoops ( https://www.thingiverse.com/thing:4854376 ) These just bolt onto the inside of the shock mount. Future goals are to make magnetic and velcro body...
thingiverse
Hub cover and bolt spacers to install this arca swiss clamp on the Skyatcher AZGTi mount: https://www.aliexpress.com/item/S8162-45-degrees-dovetail-plate-and-dovetail-clamp-set/32792533739.html?spm=a2g0s.9042311.0.0.13a74c4dLrjbT3
cults3d
I've used the mentioned things: G-Clamp fully printable Nema 17 Mount Beyond only joining the parts, I've added some space between the two bodies to be able to fit a wheel that should spin further away from the clamp. ... The only new file is...
thingiverse
I've used the mentioned things: * [G-Clamp fully printable](https://www.thingiverse.com/thing:1673030) * [Nema 17 Mount](https://www.thingiverse.com/thing:567403) Beyond only joining the parts, I've added some space between the two bodies to be able...
thingiverse
This cable chain mount lets you secure a cable chain like this one...
thingiverse
... a mirrored copy of your chosen fine in your slicer (Press M in Cura). I've provided a bunch of variations, as different things will be good in different situations. I suspect this will fit on the Crosman 2240 well, due to similar dimensions.