clips for glass patio table 3d models
2401778 3d models found related to clips for glass patio table.
thingiverse
Replacement clip for glass patio table. ...Designed as replacement parts for a friend's patio table.
thingiverse
These are the clips that slide into the inside edges of the C-channel rim of a glass top patio table & support the glass. The pieces with the "H" pattern on the back are for the sides & the "Leg End" pieces should slide over the end of the top of...
cults3d
These are the clips that slide into the inside edges of the C-channel rim of a glass top patio table & support the glass. The pieces with the "H" pattern on the back are for the sides & the "Leg End" pieces should slide over the end of the top of...
thingiverse
A duplicate spacer/clip for the ones under my patio table that were dissolving due to age. The clips go into a metal band and act as a spacer holding the glass against the upper lip of the band. ...It was designed to be printed without support.
thingiverse
I noticed that the plastic supports holding the glass surface of my patio table have been breaking and falling off. I took one of the broken ones, made some measurements with some guesses as to the screw hole size and center location, and printed one...
prusaprinters
I noticed that the plastic supports holding the glass surface of my patio table have been breaking and falling off. I took one of the broken ones, made some measurements with some guesses as to the screw hole size and center location, and printed...
thingiverse
I decided to re-paint my ~20 year old aluminum glass-topped patio table. When I was removing the glass, the plastic (or maybe some sort of resin) supports holding the glass table top in from the bottom were all yellowed and most disintegrated or...
prusaprinters
Needed a new insert for my glass patio table to fit my new, 32mm diameter umbrella pole. I resized the model that I found on thingiverse so that it would fit both the 32mm pole and the 50mm hole in my glass table top. The threads...
thingiverse
This is a connnector for a glass topped patio table with rounded rectangle hollow metal legs. Made these as I needed a replacement for a diy refurbishment on my patio table and couldn't find spares to buy online. I'd recommend printing in PETG or...
thingiverse
It was made to replace a grommet in my table that had locking tabs that have since broken off. There were not replacements found for it, so I made a better one myself. Top and bottom screw together quick snugly. Print Settings Printer Brand: ...
thingiverse
One of the two design here was based on the inital openSCAD file from Glass Patio Table Rim Clip by Ettie . So I had this patio table that started to be fragile and shake. The way it is designed structural parts depends on those plastic elements to...
thingiverse
Replacement grommet for the umbrella hole of a glass outdoor table. *** Must be printed in a flexible filament. Print shown was printed in TPU. *** Glass thickness: 5 mm Glass hole diameter: 50.4 mm Grommet Umbrella hole diameter: 40 mm Grommet...
thingiverse
This is a bracket that goes on the end of a patio table leg, supports a glass table, and a metal rim around the edge of the glass table. It may require some adjustment as I have not yet tried to install it, and the place where I need to install it...
thingiverse
You also need: - 2 18650 cells - Hilumin stripe for welding 18650 cells (eg:...
thingiverse
A replacement part for broken clips that hold the legs to the top of my small glass patio table.
grabcad
Patio glass rectangular table - corner spare part to be made with 3D printer. ...(STL file included)
sketchfab
Scan of patio table using Scann3D. ...This is a failed scan that is very messed up.
grabcad
Patio table Something to use some of the bits laying around the garage, might get around to it one day.
thingiverse
These are replacement retention clips for the glass top of a Patio table / Outdoor glass table. They fit underneath the glass top between the glass and the frame. I have printed them on my Creality LD-002r resin printer with ordinary black resin...
thingiverse
Simple "block" connector for outdoor patio table where Base Leg connects to top-glass frame. Feel free to remix, edit, adjust as needed. ...This is for a "PatioHome" table and basic measurements are 45x35x27mm that fit legs sized 38x15mm
thingiverse
This is a newly made glass clip to hold 8" by 8" regular window glass you can buy at the hardware store to the bed of a Printrbot +. For some reason the clip this is descended from didn't clip it tightly enough. This is made from scratch but I got...