command adhesive shelf 3d models

Print your own command adhesive hooks! Magnetic hook uses one 1/2'' dia x 1/8'' thick magnet. ...designed to be glue in place

Adhesive plate for the medium sized command hooks. The area that the adhesive sticks too may benenfit from some sanding to improve the surface but it should work as is. Print without supports in orientation as shown. I used a 3mm brim to increase bed...

Simple little low cost shelf i made to display minis on. ...Made to use 1'' command strips.

Simple Shelf, I used a .8 nozzle on mine. ...Should work fine with a .4!

Self-adhesive kitchen shelf for kitchen roll. It needs double-sided tape. Can be put in multiple positions to suit the consumer. ... Update: It has been reinforced to improve functionality.

<p>Wall mount for Unifi FlexHD WiFi access point. ...Use 2x large 3M Command Adhesive strips on the back to attach to wall. ...Use a piece of dental floss to remove from wall.</p>

A simple wall mount hook designed to fit the profile of a 3M Command Adhesive Strip (Large). Currently using a bunch of them to hold hats on my wall. ... I suggest printing on the side with no support and 15% infill.

Sign Clip for use with medium 3M Command Adhesive Strips. Holds up to two signs against a flat surface. Tested for six months in a healthcare setting with 24/7 use. ... Great for holding precaution signs on glass doors, especially when the sign can...

This shelf is held up with four "3M command strip" style adhesive strips (the standard-sized ones). Mine has been on my wall in my bathroom for 6 months or so without any issues. The steam etc from the shower hasn't caused any issues with the...

This remix extends the hook shell to 107mm to accommodate 90mm x 20mm (adhesive zone is only about 75mm) 3M brand strips rated for 5lbs or 2.2kg. If you would like to try to print it hollow so that the cover is flush to the wall when installed,...

This is a simple shelf that uses Large 3M Command Strips to hang.

Command Wall Shelf 17mm - Use 2 x 16mm wide command strips Command Wall Shelf 22mm - Use 2 x 20mm wide command strips. You may need to shorten the length of the wider command strips a little as he length of each support is only 60mm (2.35"). ...Print...

... excess glue. On the back of the hook plate, place two long Command Strips directly behind the shelf bracket. Follow all steps of the Command Strips for best results. ...Be sure to test the shelf carefully before placing any valuable items on it.

... excess glue. On the back of the hook plate, place two long Command Strips directly behind the shelf bracket. Follow all steps of the Command Strips for best results. ...Be sure to test the shelf carefully before placing any valuable items on it. 

This is a 7" x 4" shelf designed to fit on the base of a command strip. It is very rugged considering it is 3D printed, and can hold 15 pounds or more worth of objects if installed correctly. Put this anyhwere you want for damaged free shelving in...

This is a 7" x 4" shelf designed to fit on the base of a command strip. It is very rugged considering it is 3D printed, and can hold 15 pounds or more worth of objects if installed correctly. Put this anyhwere you want for damaged free shelving in...

... and also changed the orientation so that it prints much faster and has more strength. I use them to hold my Monster High dolls. Instructions You can still use push-pins to adhere it to a wall, but small command strips will probably work better.

{https://www.prusaprinters.org/prints/35416-toy-shelf} This is specifically designed to hold a phone, you can decide if that is in your bathroom or a spot in your kitchen or wherever. It will hold plenty of weight, the limit is really going to be...

I took the original designed by Lawrent34, and shrank it a bit, made the back the size of a 3m command adhesive strip (horizontally).

This is a bracket meant to allow you to mount a Vizio 36" speaker bar to a wall using only 3M Command Adhesive strips (3 medium strips per bracket required) two brackets required per speaker bar.

This is a shelf I designed to be mounted to the wall with 4 small adhesive strips. This print is great for places where you need to add a shelf, but can't necessarily drill into the wall, like dorms, campus housing, rentals, etc. Some support...

... option. ...I designed this so I could attach wires to the wall with cut up pieces of command strips by 3M. The flap under the wire keeps the wire from attaching to the adhesive, but more importantly gives more surface area for the adhesive to cling to.

... option. ...I designed this so I could attach wires to the wall with cut up pieces of command strips by 3M. The flap under the wire keeps the wire from attaching to the adhesive, but more importantly gives more surface area for the adhesive to cling to.

You can use thumb tacks or 3M Command Adhesive Strips. I used the mini size, but you could likely trim a larger size. I made clips for 4mm ,5mm ,6mm, and 8mm diameter stems. I recommend sizing up so your plants can grow into them. Strips:...

Stick it up with 2 of the smaller 3M/Command adhesive strips. Make sure to print this on its side (90° from how it will eventually hang) for optimal strength. You should not need any supports. ... CAD design available on OnShape:...

... of fine art masterpiece! Link for 3M command adhesive strips (Medium) https://www.commandbrand.com.au/3M/en_AU/command-au/products/~/Command-Medium-Refill-Strips-White-9pk-17021P/?N=5924736+3291859048+3294529197&preselect=5584742+3293786499&rt=rud

These clips have been perfectly designed and proportioned to be the ideal size for a single (medium) 3M command adhesive strip (link below) - genius really! Peel the tape off one side of the strip and chuck it onto the back of the clip, peel the...

... a moderately sized printer. Features include; Uses small Command Strips, allows access to Command Strips for easy removal, Print orientations designed for maximum strength, Print requires no support material, Assembly requires no glue or adhesives.

Remix of MacGyver's Remix for mounting the CPAP hose clip with command strips rather than screws. Print the base upside-down, the clip on its side, and one of the pegs upright. ...Stick to wall with 2 small command strips.

... Blank one can just be flipped if necessary), as well as the source so you can put whatever logo you want on it. You can easily stick it on a wall using two 3M Command Strips. ...I've included the necessary parts from the original by Someone2492.