compsognathus 3d model

If you need help or want something scanned, send me a message here on Thingiverse or on my FB page and I'm happy to help, ESPECALLY for a good cause (charities, educational models, STEM stuff for kids, etc.). Tips work...

They were sold to me as "boat nails", feel free to substitute them for something else and adjust the model accordingly. For the spark gap I used a couple of bits of single stranded wire, these can be substituted for something else, multi-strand...

To assemble: Note - this is a somewhat challenging model to assemble, with a lot of parts, and a lot of tight-fitting pins to hold the parts of the toy together. You may also have to clean up a lot of support off the oddly-shaped pieces as not much...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

I have since printed out another model in ABS which I am hoping will be more durable. PETG would be another more durable substrate to consider using. Special thanks to Jim Harmon at Keystone College and Emmitt Zugar at Salem Community College for...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 11 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

... for the bottom of the case i used this * Various wire, soldier, etc. etc. My Other Stuff: https://cults3d.com/en/users/revere521/creations https://www.printables.com/social/406094-revere521/models https://www.thingiverse.com/revere521/designs

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

My prototype box had a problem in which the combination could be guessed by feel due to the slack in the model. This problem was fixed with a number of features that make guessing the combination by feel very difficult. As an additional precaution, I...

The model was inspired by [this map pocket on Amazon](http://a.co/5P0dMfJ), but larger and with more holes for the bungee cords. ...I have no affiliation with this product and my design was done by hand, so please don't sue me if that's your map pocket...

The freecad file is made with: Realthunder Branch Word size of FreeCAD: 64-bit Version: 2023.131.26244 +5365 (Git) AppImage Build type: Release Branch: LinkDaily Hash: 73c4ca254c5de8849d104973482e98399fb24863 Python version: 3.10.8 Qt version:...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

Please note that this model doesn't include the hooks on the bottom for the external antenna coupling. My car doesn't have one but I think it can be added easily. You can find the assembly instructions in the print instructions or here at...

This model currently comes in 4 variations. Standard rail facing forward. Standard rail angled 5 degrees to the side off the rail. Standard rail with sidekicks facing forward. Standard rail with sidekicks angled 5 degrees to the side off the...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame which require support. You may need to use a raft or brim to secure the part...

I could not find caps / hoders which suited my project, starting from inspiration of certain models existing in AA, I made a design under fusion 360 which corresponds in the size of integration, as well as the possibility of making spot welding. ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

now you can the stands/feet print without support or if you want the texture of the powder-coated pei sheet you can print it on its side without support.Release Candidate 1.5 - 15 January 2021Updated some sections to the model so it's stronger when...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

A .3mf file and pre-sliced .bgcode file is available along with the STL models. Also prints well on a Bambu Lab P1S.Assembly/MountingThe inner fixture can be held upside-down to desired mounting position for marking the mounting holes. I found it...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

These two parts are rather small but also simple ball joint parts that rely on friction and cannot be tightened. For those of you that want a to be able to tightly secure your camera in a certain position, there are also parts that form a double-ball...

- [Winwill USB to PC Fan Cable](https://www.amazon.co.uk/dp/B08SVZD8MK?psc=1&ref=ppx_yo2ov_dt_b_product_details) I printed these prototypes in Black PLA with a Prusa Mini but would recommend a larger printer model to avoid wasteful support material....

My original plan was to also model a strap clip for the bottom of the mount, but I found that it was unnecessary, as the entire thing can be attached directly to the head strap and head pad with a velcro strap. I used a couple of long velcro cable...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 1 stencil_size = 40 stencil_shape = 6 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

I restarted from scratch and designed this model from those other inspirations. This version allows a 5015 fan to be installed without interference to the left or right gantry positions. I placed the fan above the slightly relocated CR Touch...

The COMPLETE Dragonpeak Barbarians I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The people of Dragonpeaks are direct descendants of the Humans who lived in Aera under...