concept 2 rower pm3 battery replacement 3d models
1133889 3d models found related to concept 2 rower pm3 battery replacement.
thingiverse
This thing slips right onto a concept 2 PM3 and provides a post to mount a bicycle style phone holder. ...Could easily be modified to have its own holder.
thingiverse
Phone holder for a concept 2 rower. ... All .stl files with "1X": Print one of each stl in PLA or PETG .stl file with "2X": Print two in TPU .stl file with "4X": Print four in TPU Use a rubber band as shown in picture.
thingiverse
Tablet support for Concept2 Rower works with - elastic rope blocked by 2 knots (about 2.5 or 2.7 diameter) - 2x TCHC M3x16 - 1x TCHC M3x12 - 3 nuts
thingiverse
An iPad holder on top of [concept 2 smartphone cradle](https://www.concept2.com/bikeerg/accessories/smartphone-cradle) with simple design(minimum support + no assembly required) Coming in 3 different flavors.
thingiverse
Adjustable Mobile Phone Mount for your Concept 2 Rowing Machine. Works for devices with a width of up to 100mm. To get a secure fit, attach a rubber band between the two parts. ... Enjoy!
thingiverse
A little Arduino micro controller flashes the LEDs and rechargeable AA-batteries keep the device going. They last until you look like a Body Builder, (ha-ha-ha). The holder is put over the PM5, the Thing is put into the holder. That’s it! Enjoy...
thingiverse
Used to hold 10" ipad mount slides onto the PM5 support bar Top section uses: M3x30 socket cap flat head screw (3TSSFM03x30) x1 3x0.5 low square nut (FC-35622410) x2
grabcad
The PM3 has thre econnections for pilot valves,regulates the flow of the medium by modulation or on/off function
thingiverse
Wanted something that would hold my Phone running the Concept 2 ERG Data app and a Ipad playing a video. Unit slides on and off very easily. Top phone holder mount can be removed. Bolted a quadlock on first then redesigned it so it could be...
thingiverse
I designed this object to guide and maintain the heart rate sensor cable against the rail.
thingiverse
The side stops are replaced for longer ones, and I added 2 Battery protections, since I bought a LiPO soft pack. Side Protections (print 2 of them) have embedded breakable support by design. Bottom protections (print one of each) do need to add...
grabcad
The PM3 can be used in suction,liquid, hot-gas,and liquid/vapour lines. ...the PM3 has three connection for pilot valve.
thingiverse
Alti-2 was gracious enough to replace my battery cover a couple of times. They have now discontinued the product, and I have once again broken the battery cover. I went ahead and backwards engineered the cover added some thickness to the weak...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: drive_type = phillips head_type = socket nut_type = normal slot_depth = 2 head_height = 3 thread_length = 15 inner_diameter = 8 outer_diameter =...
thingiverse
Replacement battery Pack: to be glued together, the battery’s can be mounted the wrong way! Short circuit is possible when not mounted with care! Short circuit is a real possibility when choosing the wrong conductor lengths! Damage to the toy is to...
cults3d
The torchlight fell down and the battery pack broke in many ways. ...The torchlight is good so i decided do repair it.
thingiverse
The torchlight fell down and the battery pack broke in many ways. ... The torchlight is good so i decided do repair it.
grabcad
Simple design to replace the cap on the back of your rower display and use this as a phone holder. I recreated the existing battery cap on the back of the display and added the additional bits for the phone. All you need is a rubber band and you're...
thingiverse
This project will allow you to put a smartphone on top of the Concept2 PM3 monitors. I needed a place for my cellphone to watch videos and to capture ErgData. So powered up Fusion360 and put in the measurements to create a base unit and an...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=735038 Instructions Using the following options: n_angle = 0.501 n_pipe = 1 l_mani1 = 5 a_mani = 0 ds_fan2 = 5 ds_fan1 = 5 t_wall = 2.5 az_mani = 0 a_cone = 100 ls_fan2 = 138 d_fan2 = 150...