coned lens board for mpp mk viii 4x5 view camera 3d models

Markings for 35mm, 645, 6x6, 6x7, 6x9, and 4x5. Not well optimized for material use but prints nicely on its back with the markings facing upwards. 

This is a straightforward miniature frame designed specifically for 4x5 tintype portraits, boasting outer measurements of 4.125 inches by 5.125 inches, while the hole dimensions are precisely 3.875 inches by 4.875 inches.

This is a custom 9x12 face mask designed specifically for use on a 4x5 dry rack, engineered by expert creator Roland Deegest - check it out at https://www.thingiverse.com/thing:2423724.

I customized my 67mm lens cap by adjusting its parameters and the 25mm width of my BlackRapid R-Strap. Additionally, I separated the strap's buckle to enable clipping the holder directly onto it, instead of threading it through. The R-Strap features...

... handle with a light and a Zoom mic, and putting it in the case is a pain. So - simple slip-on lens cover. ...I printed it from TPU at 1mm thick so it flexes and protects at the same time.Note: You'll probably have to rotate it so the open end is up.

Screw sky from paw partol on you cameralens.The blossom has a 58mm filter threat to screw sky in front of your camera.Now you have the attention from the kids while you have a photoshooting with them.Easy to print and color with paint.

Screw sky from paw partol on you cameralens. ... The blossom has a 58mm filter threat to screw sky in front of your camera. Now you have the attention from the kids while you have a photoshooting with them. ... Easy to print and color with paint.

Screw sky from paw partol on you cameralens.The blossom has a 58mm filter threat to screw sky in front of your camera.Now you have the attention from the kids while you have a photoshooting with them.Easy to print and color with paint.

I have an old film camera (Konica Autoreflex T) that had a blurry viewfinder, and before it was very foggy, now it is crystal clear after using this spanner wrench to open the top cover. Similar to:...

This is 9x12 mask for 4x5 dry rack created by Roland Deegest: https://www.thingiverse.com/thing:2423724. Print Settings Printer Brand: MK3 Printer: Prusa i3 Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 10% Filament: Clas Ohlsson PLA...

not much, because the license plate lights are angled up and shine straight into the camera lens, causing glare and weird exposure issues. These simple little plates attach with some double sided tape, and block the glare from the lights. This...

In my recent modifications to the .scad file, I adjusted it for a 49mm diameter. ...However, I also provided the .stl file for others who may not use OpenSCAD or prefer convenience.

Upgrade your high-tech webcam with the complete mod kit detailed in this article. ...For more discussion, visit http://lukse.lt/uzrasai/2013-07-modifying-logitech-c920-to-for-cs-lenses and engage with others who have undertaken the same project.

This is a reinterpretation of https://www.thingiverse.com/thing:443442. ... It's crafted specifically for the NEW CANON 18-55 IS STM, which boasts a distinct hood mount featuring two contact strips in place of three.

This plate holder is a handy way to make pouring chemicals onto plates for photography much easier and reduces waste. Place the 4x5 plate in the holder and the chemical can flow over the whole plate including edges without leaving finger marks. Then...

There are 2 versions of the STL file - one made for the original GoPro Lens, and one made specifically for Camera Butter twist-on filters. The one for the Camera Butter filters stays on a little bit better because it grips the indentations on the...

Lens board for Heidosmat 150mm f2.8 projector leans, to mount in 4x5 Graflex Speed Graphic cameras with Type C board mount. I secured the back of lens with a hose clamp and a rubber band. ...I'm sure there are tons of other ways to do the same.

There should be no vignetting if you use it in 4:3 linear mode with hypersmooth off (this is the mode you should be using for this lens) Here are the ND filters and lens protectors that are used with this adapter:...

... and then combine them afterwards. This frame is designed specifically for placing the film perfectly each time it's scanned. ...And because the film will be slightly elevated during scanning, it also prevents Newton's rings from appearing.

This is a lens cap intended for use with the [disposable camera lens mount.](https://www.thingiverse.com/thing:5684778) Includes lens type and focal length on top. ...

86" Display3rd Generation

This remix comes from thingiverse.com/thing:3677352. ...The TOYO 158x158mm lens plate is crafted specifically for use with COPAL-3 shutters that feature a 65.3mm hole diameter.

A simple lens cap for the Konstruktor SLR camera.

The photographer attaches a Helios-44-2 lens to their KODAK Z1012 IS camera, carefully ensuring a secure connection between the two devices. ...Meanwhile, in a completely unrelated scenario, someone applies glue to join two sections of a pipe, creating...

Point it straight out for the center of view or change the Laser_Angle to 1/2 the angular field of view to see where the bottom (or top, or corners) of the frame will be. The lens feature lets you add a lens from welding goggles to adjust IR...

The aluminum base of the Intrepid 4x5 MkIV field camera is 4mm thick while the the typical tripod mounting screw on most tripods is well over 5 mm long. Because of this design flaw, when you attach the camera base to just about any mount, the screw...

The laser pointer is helpful for aiming the camera before turning it on. Point it straight out to find the center of view or change the Laser_Angle to half the angular field of view to see where the bottom, top, or corners of the frame will be. The...

Cover Cap to Hide Camera Lens Easily

I've printed numerous boxes for different film types and exposures, and I can confidently say they work fantastically well. They're incredibly useful tools that make it easy to organize and store your exposed films. To take things to the next level,...

Cover for DJI FPV lens, it may fit in another camera, but I haven't test it.