control pod for bose companion 3 3d models

Bought a Bose Companion 5 set without the stands, so I designed this riser for the satellites to get a better listening angle on my desk. Could definitely be wider but this works for me as I don't move the speakers around. ...I can customize this if...

It will not work on Bose Companion 3 and there is a new Bose Companion 50 design that also looks different. Print Settings Printer Brand: Prusa Printer: Prusa Clone Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 30% Filament:...

speaker stand for the BOSE Companion 5 system. Print instructionsCategory: 3D Printing Summary speaker stand for the BOSE Companion 5 system. Print Settings Printer Brand: Prusa Printer: i3 MK3</div>Rafts: No Supports: ...

To attach my Bose Companion system speakers on my bed, I couldn't find any mounting solution, so here's my DIY idea. The speakers are meant to be affixed with double-sided tape on walls. The printed part is slightly tight as per my preference but...

My Bose Companion 50 speakers were to high for my dual monitor setup so I looked around on Thingiverse if someone made a less high version and luckily aJ_Berlin did. I modified his design a bit more to my liking though. Instructions for removing...

I like to use my bose comanion as a headphone holder. However, the sharp edges always leave marks in the pads of my headphones. To prevent this I have designed this part. It plugs onto the speaker and gives a way to place the headphones more gently...

Bose A20 Headset Control mount for standard Cessna aircraft ashtray.

Remote control holder for the Bose 900 Sound Bar

Dock for Bose SoundLink3 Speaker Prints in 2 halves to fit just about any 3D printer. Designed with 123D, files included. This handy accessory fetches $35 from Bose, but you can build one for a few bucks. You will need: Small scrap of 1.5mm aluminum,...

This is a sleek holder for the control module on the Bose A20 aviation headset. The module slips in from the top and is held perfectly. It is tight enough to hold the controller but not so tight it leaves scratches, there is enough room to put in...

 I added a 2nd screw hole, moved the angled side brackets in line with the back and bottom, kept the holes for wires round, and made 2 different hole sizes for left and right speakers.I printed with 0.2 quality with PLA.  I used an infill...

Reprograms the existing controls to work with the subwoofer.

... of this mount perfectly holds your Bose remote control in place, keeping it organized and out of the way. Easy to install, this wall-mounted remote control holder is the perfect solution for any home or office looking to declutter their space.

I crafted a customized control puck nest for the Bose sound controller that refuses to stay in place. The PLA surface, however, is perfectly suited for securing with tape (its rubber foot has a non-stick coating), so I've designed this interface to...

I got fed-up losing the remote for my Bose speakers amongst my desk clutter so I decided to design and print a holder for my Skadis board. Will fit remote for Bose SoundTouch 10, 20 & 30. Remote dimensions: 114 (L) x46 (W) x15 (D) mm. ... Designed in...

I looked everywhere for a low profile Bose A20 Control Module mount without much luck, so I decided I would model one! I created the model so that it would gently hold the module with just enough tension in the surrounding walls, without scratching...

Remix of a design by Felix JD, I flattened the bottom and added the bose logo, which I then painted a contrasting colour.

This knob was engineered from the original knob for Vintage Bose Spatial Control Stereo Receiver Model 551 With 901 Equalizer 108787, but it could potentially work with other vintage Bose Receiver models as well. Printing with supports yields a...

Customized version of https://www.thingiverse.com/thing:3285096 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3285096

Customized version of https://www.thingiverse.com/thing:3285096 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3285096

Customized version of https://www.thingiverse.com/thing:3285096 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3285096

... for a way to store them efficiently and thus designed this simple storage box.  The box holds a control pod and five light arms and the lid is held in place by friction and 8 neodymium magnets (6 x 2 mm). ...The boxes are stackable.Happy printing.

This is a remix for the Bose Companion 20 speaker stand that was made with holes for wood sticks. instead I made it completely out of the 3D Printed model as a complete build, and added a logo (Bose Companion 20) on the front facing of the stand. ...

Bose URC-15S Remote Control Stand

Simple Foot for bose Cinemate II with Wall support

This control pod add-on is designed specifically for Southbend engine lathes that utilize a Cutler Hammer 3-phase motor reversing drum switch. It seamlessly integrates into the existing setup, allowing users to access enhanced functionality when...

Changed up the original to allow for hanging inside an R22. ...Added felt to the back and inside so it won't scratch the Bose control box or helo.

Wirelessly sync and control your music collection with the compact yet powerful SoundTouch Wireless Music System from Bose, effortlessly wall-mounted to perfectly complement any decor while freeing up valuable space on furniture surfaces or floors,...

Support for the Bose A20 headset control module. The system consists of the support and a bracket that you can fix on the plane, the bracket is reversible, to be fixed on the right or left side. The one made is for the Texan Fly Synthesis. The...