convert jpg to gcode online 3d models

I could not find gcode for the Anycubic i3 Mega X to assist in the levelling of the bed so I created one and you can find the details below; This to help assist level the bed with the paper method. you can also attach a Dial Caliper and use this...

**FULL CREDIT TO THIS POST** https://www.thingiverse.com/thing:2798940 I struggled to get both the left and right grip slices right in Cura after mirroring, it took me some time to crack the code. I wanted to save others from wasting their time so I...

It preheats the nozzle to 160 degrees, and drives the nozzle into the bed to remove stuck filament ( this is done with the strain gauge of the smart effector) then performs mesh bed leveling. Next, the nozzle is pressed against the print bed to...

First, open the .3mf file with Cura and customize all settings to your preferences. I printed this project with 0.28mm layer height for optimal results. The gcode file is configured with tree supports only where necessary. ...If you're using an Ender...

This is my Gcode for print a big Alien Xenomorph en Ender 3 / 3 Pro (45cm) Scale : 170 % Layer : 0,1 mm Nozzle : 0,4 mm The different parts are place on plate in a way to minimize visibility of support and layer...

It's currently printing now, so this might be a little premature in uploading the Gcode files here, but I wanted to give people the chance to try my GCODE out and respond. Please note that this is not a representative of how Simply3D prints files...

A Temperature Tower designed to find the correct temperature for your filament! The included .gcode is sliced using Simplify3D with the "Multiple Processes" tool to set the temperatures at different layer heights. Take a look at the included image.

Just run the gcode from sd or octoprint Use feeler gauge or paper while adjusting knobs Category: 3D Printing Tests

You can easily use the gcode by uploading it to a sdcard or with octoprint. For filament loading, be sure to insert the filament so it appears on the start of the bowden tube. Thanks a lot to the original author @Qualith ! ... You can find advice on...

You can easily use the gcode by uploading it to a sdcard or with octoprint. For filament loading, be sure to insert the filament so it appears on the start of the bowden tube. Thanks a lot to the original author @Qualith ! ... You can find advice on...

... and I'll be happy to make an another version. ------------------------------------------------------------------------------------------------------------------- If you would like to give me a small tip I would be really happy and grateful! ...

... to me and I'll be happy to make an another version. ------------------------------------------------------------------------------------------------------------------- If you would like to give me a small tip I would be really happy and grateful!

To change the Start-Gcode, go to Machine Settings (Cura: Settings -> Printer -> Manage Printers -> Machine Settings). You'll need to add two lines of code to the Start-Gcode textarea in the bottom left corner. First, type G21 to switch to the...

... Note: Only use the G-code if you're running an original Prusa i3 MK3/S! Happy Printing! Changelog: Added version without numbers in case someone wants to use this tower for other materials Added picture with measurements Added .gcode for PETG

For self reference, and for whomever needs it, this is a ready made gcode rendition I made of the original part, with: - 0.4 nozzle, 0.2 layer height - single wall - no supports (obviously) - no infill - half height base (0.5mm instead of 1mm) -...

The gcode file is tailored to a Replicator 2 with .1mm resolution, using Fused3D's Wood filament at varied print temperatures for an authentic wood grain effect. The STL file has been rotated from the original Thingiverse model for seamless printing!...

Sexual Enhancement Medicine

Instructions This simple g-code interpreter implements the G00, G01, and M114 commands - enough to draw with a marker, including pen lifts, using output from a text to g-code program. Setup for the serial replies from an arduino is done in a basic...

... based on STOCK Cura 4.4.1 Profiles for PLA and PETG in "Standard Quality" settings. Only things that were changed from the stock profile are adding a brim for stability, and increasing bed temperature to 80C and reducing fan speed to 80% for PETG.

... of the 26650 battery. If you are not comfortable building the circuit yourself, consider purchasing a pre-built 18650 to 26650 converter. These converters are widely available online and can be a cost-effective solution for converting batteries.

This spool holder, compatible with the Printrbot Metal Simple, features both .gcode and .stl files for easy printing. ...Visit www.macdevstudio.com for more details.

This is a Gcode manually written to greatly aid in the painful process of leveling your printers build plate. it will slightly heat the nozzle/bed and cycle twice between 5 locations on the build plate (corners and center) and wait for you to finish...

This GCode was generated with CURA's post-processing scripts, and has only been tested on my own Ender-3. 3 versions for a few different nozzle sizes - make sure to get the 0.4mm if you're not sure. Remixed from the fantastic multi-purpose test...

Gcode for Stock Ender 3 Temperature Sweep \r\n\r\n\r\nLayer: \r\n0.1mm\r\nFirst Layer 0.3mm\r\n\r\nInfill: 20% Density\r\n\r\nSpeed:\r\nFirst Layer 20mm/s\r\nWalls 25mm/s\r\nTop and Bottom 50mm/s\r\n\r\nBed Temperature:\r\n60°C\r\n40°C (Temp 40...

Sliced with Prusaslicer 2.5 using new Arachne system for quick testing of your filament or printer, Gcode files are in 0.4mm nozzle version and 0.6mm nozzle version.

... head will not collide with the nozzle wiper. ... !! ATTENTION !! !! TEST THE GCODE BEFORE USE !! GCODE: G90 G0 Z12.5 G0 X10 Y0 F6000 G0 X0 F6000 G92 E0 G1 E10 G90 G0 Y10 F6000 G0 X15 F6000 G0 Y0 F6000 G0 X0 F6000 G92 E0 G1 E-4 G90 G0 Y50 F10000

That's why I wrote this GCODE, partly for learning and partly to speed up my levelling as a stopgap until the warranty expires and I can modify it freely. It's designed specifically for Ender 3/Ender 3 Pro models but can be adapted for any printer...

This is a model of a UsbC to Micro USB converter I had gotten from EBay.

LERDGE to Fysetc 12864 mini converter 4 x M3x5 2 x M3x10

... ... Gcode generated for FABLAB Burgos, for Witbox 1 with white PLA. ... Speed; 54 mm/s (no speed adjustment) Restriction of 2.00mm at 40mm/s with head lift of 0.20mm Temperature of 210 degrees (white PLA) without heated bed, with PID configuration