cooler master masterbox pro 5 mesh front panel 3d models

Front panel to fit a 1 DIN car radio in the non-standard slot of Opel Corsa D (2010). Car radio attached to the frame of the original car radio. Fits to the millimeter, no clips. No modification needed to mount it, so you keep the possibility to...

This is a hex pattern high airflow PC case front panel designed specifically for the Lian Li M205. It is meant to be printed in two parts and then glued together, offering an easy installation process. I took a different approach by removing...

Similar design for ctc i3, but this replaces original wooden front panel Print Settings Printer Brand: Prusa Printer: Prusa Clone Supports: Yes Notes: Can be printed without supports if printed as shown. ...Needs supports for holes (especially that...

New front panel for the Sieg SC4 bench lathe, that uses physical buttons rather than the membrane keys it has as stock. This modification requires the removal of the selector mechanism that allows the spindle to be stopped whilst the lead screw is...

Remix of Ender 5 Plus cooler by Dolugius. Noticed outlets were still not low enough to get below the heat block. Angled down to be right below the heating block. ... Touching Build Plate - For supports Just needs two 5015 fans and a 4020 fan.

It's not flawless - the screws for the case panel are excessively long and cause the adapter plate to buckle if tightened fully, but on my specific setup, where the fan is mounted at the top, it sits evenly on all four screws. ...The result is a...

Hello, i designed a front panel clip-on cover for my Rigol DS1054Z. In the downloads you will find two versions, one cut in half for printers with small print volume and one uncut for bigger printers. Clips must be printed by themselves and...

The bottom side requires clearance from the front end shielding clips. The display module aligns perfectly with the window, but the window, the seat for the module and the module need to be adjusted so they align precisely with the pin headers on...

Hello, i designed a front panel clip-on cover for my Rigol DS1054Z. In the downloads you will find two versions, one cut in half for printers with small print volume and one uncut for bigger printers. Clips must be printed by themselves and then...

This is a custom CR10s LCD panel mount designed specifically for the stock CR10s LCD, not compatible with the CR10. I mounted mine on the front rail facing forward, inspired by similar designs that didn't fit my machine. This one was built from...

Hard Drive Sled for Coolermaster CM 690 II for both 3.5 and 2.5 inch drives. Print Settings Printer: Kossel XL Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 20 Filament: Polymaker Polyflex TPU Black Notes: The Hinge Hole is designed...

... attached to the heat sink, as it may slide off otherwise. Let it cool completely before removing it, or it will warp if pulled off too soon after printing. Printing took 2.5 hours using Octoprint. ...This design fits comfortably on a 120mm bed.

... a 4 layer rectangle that I superglued to the back side. use tape to hold the cover on the heat sink of it's sliding off. LET IT COOL it's gonna warp if you pull it off right after printing it. Took 2.5 hours with octoprint. ...Fits on 120mm beds

After scaling to compensate didn't help and not caring about it being tool less, I just changed the pins to counter bores located on the original pins.Added a second set of mounting points for 2.5 inch drive adapters.Without the pins it may be...

The bottom side needs clearance from the front end shielding clips. The display module aligns well with the window, but the window, the seat for the module and the module need to be moved so they align nicely with the pin headers on the main PCB. The...

A straightforward layout concept for the door panel is proposed in this design, specifically tailored for the Range Rover Evoque model.

This front panel for the SCM SCR335 USB smart card reader slides neatly into standard 5.25" PC slots. ...The smart card reader is secured using its original case screw holes along with two robust self-tapping screws that are DIN7982 compliant, measuring...

It is a concept of the bike front look I tried to give it a look of an F1 car

RetroPie TV Front Cover by Joo, Published February 4, 2015 on Thingiverse: https://www.thingiverse.com/thing:666802

It is a concept of the bike front look I tried to give it a look of an F1 car

Big Cooler for the Creality Ender-5. Compatible with the original hot-end and the Micro-Swiss all metal hot-end. Extra parts needed: - Chinese blowing fan 40mm x 20mm - Some M3 screws: - 4 M3 x 20mm screws - 2 M3 x 14mm screws (*) ...

The front facade of the Spyder R8 automobile is being worked on diligently, with Creo Parametric 2.0 as the software employed in its design and development process. ...This cutting-edge technology ensures precision and efficiency throughout the...

... glued to the ATX itself - in the contact parts, left, right and in the lower part. ...Using hot glue. The panel above for convenience is then glued. ...The label with the voltage values is printed separately (with color filament change) and glued.</p>

I'm creating a simple panel to house 15 rocker switches and 7 encoder switches. The rocker switch openings measure 19mm by 12.5mm, while the encoder switch holes are a compact 7mm in diameter. ...This project marks my first foray into 3D printing, so...

Designing interior door panels in SolidWorks provides a comprehensive approach to creating functional and aesthetically pleasing components for residential or commercial spaces. This CAD software allows for precise measurements, customization options...

How to Use: Depending on what route you take, you need to download the specified files which contains either the **.STL (for 3d printing)** or the **.SVG (for laser cutting).** If you are laser cutting make sure the thickness of your metal is a...

ATX fron panel fit on an old ATX PSU, nice to have in my lab. The PSU project is one of the many find on internet, personally i followed the @tartaglia project (thanks) and i added some modification. ... Pay attention that the fan cut is based on my...

I relocated the left front panel from its original design, creating an opening directly above the SD card slot of the Panel Due 5'' display. As you can clearly see in the accompanying photographs, it fits seamlessly into place. The SD card slides...

As I required supplementary dimensions of the potentiometer bolt tool by marcelodamian, I chose to create all from 5 mm to 13 mm... ...just in case...\r\n\r\nEdit October 25, 2019: Included 14, 15, 16 and 17

http://www.thingiverse.com/apps/customizer/run?thing_id=1264391 Instructions Using the following options: Thick = 3 BPanel = 0 Police = Impact m = 1.0 Vent = 0 FPanel = 2 PCBLength = PCBPosY = 7 PCBPosX = 8 BShell = 0 Text = 1 Width = 90 PCBFeet = 0...