cp33 accessories 3d models

Gentlemen, I decided to work on some Kel Tec CP33 accessories and this is the first piece, its a P-Rail brace adaptor, I designed 4 versions starting from large and all the way to micro. You will only require 2x M3 x 20mm socket head screws to mount...

kel-tek cp33 short and long rails i split them to print and super glue together

This is a magazine extension for the CP33. I designed it based off of Kel-Tec's proprietary magazine extension. ...It should function just as well as the proprietary version.

I made a Magpul-style baseplate for my KelTec CP33 magazine. I used part of martialmedia's design and adapted it to fit my application. ... https://www.thingiverse.com/thing:1443089

(this model has not been printed and tested) - CP33 Shroud mlok no rail - This model does not include the area for the igitalnimbuslabs brace rails. If you dont need that attachment then this is the model for you.(this model has not been printed and...

This is a magazine extension for the CP33. I designed it based off of Kel-Tec's proprietary magazine extension. It should function just as well as the proprietary version. ...This is the same as my previous magazine extension, but it has no grooves as...

This is an adapter for the keltec cp33 to use a tailhook arm brace. hardware youll need: the acutal ATF approved tailhook 10mm alumium rods or feel free to made that smaller for whatever rods youwant to use. ... 2small screws 2mm x 8mm for the back...

This is a magazine extension for the CP33. I designed it based off of Kel-Tec's proprietary magazine extension. It should function just as well as the proprietary version. This is the second version. ...It is slimmer, fits better, and has a stronger lip...

This was originally as a mount for a Bushnell Trophy TRS-25 Red Dot sight to fit on a KetTec CP33 with the original iron sights still usable. It mounts to the picatinny rail, and has one picatinny slot in the middle of the top for the red dot to...

Shroud replaces stock mlok barrel shroud on the CP33. Use stock screws to mount the shroud. The print still provides a mlok slot in the same location. Light compatibility designed for Streamlight TLR RM 2. Pressure pad half installed with shroud...

This is a magazine extension for the CP33. I designed it based off of Kel-Tec's proprietary magazine extension. It should function just as well as the proprietary version. This is the second version. It is slimmer, fits better, and has a stronger lip...

CP33 Configuration Keltec CP33 Forward Angled Grip, #4677465 by Todd Gomez, Likestoshootstuff https://www.thingiverse.com/thing:4677465 CP33 magazine baseplate, #3980528 by Feral Daryl, feral_daryl https://www.thingiverse.com/thing:3980528 REHV ARMS...

Harware needed: 1 - M4 x 35mm bolt (Found at lowes or homedepot in packs) 1 - M4 Nut (Found at lowes or homedepot in packs) Original hardware for the stock mlok barrel shroud, it should be 2 screws Any other hardware to mount an mlok attachment...

CP33 Configuration: Keltec CP33 Forward Angled Grip, #4677465 by Todd Gomez, Likestoshootstuff https://www.thingiverse.com/thing:4677465 CP33 magazine baseplate, #3980528 by Feral Daryl, feral_daryl https://www.thingiverse.com/thing:3980528 REHV...

I found it annoying to remove the mag from my CP33 because there just isn't much real estate to get a hold of. This baseplate is wider than the factory one, especially at the front, allowing you to get two fingers on the mag and your thumb on the...

angled forgrip for keltec cp33 with thumb rest and rail left and right

XYZ car accessories

Accessories from best Aftermarket Auto Parts Online Store | theautopartsshop.com https://www.theautopartsshop.com/accessories

Print in flexible filament. ...This will allow for you to mount a Hatori Super Small Mini LED Flashlight at an ultra-low profile on the top picatinny rail of the Keltec cp33, so that it is adjacent to the right side.

Y = , Z = Each compartment measures x “Z” was designed to fit CP33 magazines using the Thiniverse #3980528 “quick pull” base plate by Feral Daryl, feral_daryl https://www.thingiverse.com/thing:3980528 . For magazines using the KelTec flat base plate...

This is a PB ( Brace )mount and QD tube for the CP33. It is retained by two small zip ties in front of the sights and around the snap on frame mount. I did not design in the use of the frame screws, but left the detail available for longer screws if...

I like the design shared before as it widened the grabbable area, however I missed the extension included in the original, so I added it! ...I am thinking I will rubber coat these as well once I can, adding an extra-extra-extra layer~

This adapter requires 2 - 5/16" aluminum rods. The tubes of the body portion of the adapter might need to be drilled out a bit to fit the rods. The spring mechanism is a binder clip with a cut-off Allen wrench through it. I used two small wood...

Folding Tail hook brace adapter for kel-tec cp33. ...This is only an adapter, this part is not regulated or restricted and is not a firearm.  You will need a M4x30mm screw, M3X30mm screw, and a small spring external diamiter 4mm or less, 8mm x 3mm...

pegboard holder for Kel Tec CP 33

using carbon arrows as shafts . ...I havent worked out a locking mechanism yet

cut the fat, high speed, low drag

This is a remix for an angled grip with a steeper angle, and no rests or rails on the side. ...this is a forward angled grip, it is not intended as a vertical foregrip, it even says so on the side.

#FIVERRCULTS DESK ACCESSORIES_office accessories

Accessories